* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
@ 2013-05-07 11:24 Pascal K
0 siblings, 0 replies; 11+ messages in thread
From: Pascal K @ 2013-05-07 11:24 UTC (permalink / raw)
To: ptxdist
[-- Attachment #1.1: Type: text/plain, Size: 36471 bytes --]
Thanks for the help, i attached the working make and in file here:
Thanks, the solution for my beginners problem was awesome fast.
Best regards,
Pascal
*hostapd.in:*
## SECTION=project_specific
config HOSTAPD
bool
prompt "hostapd"
help
FIXME
if HOSTAPD
config HOSTAPD_DRIVER_HOSTAP
bool
prompt "HOSTAP driver"
help
Driver interface for Host AP driver
config HOSTAPD_DRIVER_WIRED
bool
prompt "Wired driver"
help
Driver interface for wired authenticator
config HOSTAPD_DRIVER_NL80211
bool
prompt "NL80211 driver"
select LIBNL
help
Driver interface for drivers using the nl80211 kernel interface
config HOSTAPD_DRIVER_NONE
bool
prompt "no driver"
help
Driver interface for no driver (e.g., RADIUS server only)
config HOSTAPD_IAPP
bool
prompt "IEEE 802.11F/IAPP"
help
IEEE 802.11F/IAPP
config HOSTAPD_RSN_PREAUTH
bool
prompt "WPA2/IEEE 802.11i RSN pre-authentication"
help
WPA2/IEEE 802.11i RSN pre-authentication
config HOSTAPD_PEERKEY
bool
prompt "PeerKey handshake for Station to Station Link (IEEE 802.11e
DLS)"
help
PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
config HOSTAPD_IEEE80211W
bool
prompt "IEEE 802.11w (management frame protection)"
help
IEEE 802.11w (management frame protection)
This version is an experimental implementation based on IEEE
802.11w/D1.0
draft and is subject to change since the standard has not yet been
finalized.
Driver support is also needed for IEEE 802.11w.
config HOSTAPD_EAP
bool
prompt "Integrated EAP server"
help
Integrated EAP server
config HOSTAPD_EAP_MD5
bool
prompt "EAP-MD5 for the integrated EAP server"
help
EAP-MD5 for the integrated EAP server
config HOSTAPD_EAP_TLS
bool
prompt "EAP-TLS for the integrated EAP server"
help
EAP-TLS for the integrated EAP server
config HOSTAPD_EAP_MSCHAPV2
bool
prompt "EAP-MSCHAPv2 for the integrated EAP server"
help
EAP-MSCHAPv2 for the integrated EAP server
config HOSTAPD_EAP_PEAP
bool
prompt "EAP-PEAP for the integrated EAP server"
help
EAP-PEAP for the integrated EAP server
config HOSTAPD_EAP_GTC
bool
prompt "EAP-GTC for the integrated EAP server"
help
EAP-GTC for the integrated EAP server
config HOSTAPD_EAP_TTLS
bool
prompt "EAP-TTLS for the integrated EAP server"
help
EAP-TTLS for the integrated EAP server
config HOSTAPD_EAP_SIM
bool
prompt "EAP-SIM for the integrated EAP server"
help
EAP-SIM for the integrated EAP server
config HOSTAPD_EAP_AKA
bool
prompt "EAP-AKA for the integrated EAP server"
help
EAP-AKA for the integrated EAP server
config HOSTAPD_EAP_AKA_PRIME
bool
prompt "EAP-AKA' (AKA-Prime)"
help
EAP-AKA' (AKA-Prime) for the integrated EAP server
This requires CONFIG_EAP_AKA to be enabled, too.
config HOSTAPD_EAP_PAX
bool
prompt "EAP-PAX for the integrated EAP server"
help
EAP-PAX for the integrated EAP server
config HOSTAPD_EAP_PSK
bool
prompt "EAP-PSK for the integrated EAP server"
help
EAP-PSK for the integrated EAP server (this is _not_ needed for
WPA-PSK)
config HOSTAPD_EAP_PWD
bool
prompt "EAP-pwd for the integrated EAP server"
help
EAP-pwd for the integrated EAP server (secure authentication with a
password)
config HOSTAPD_EAP_SAKE
bool
prompt "EAP-SAKE for the integrated EAP server"
help
EAP-SAKE for the integrated EAP server
config HOSTAPD_EAP_GPSK
bool
prompt "EAP-GPSK for the integrated EAP server"
help
EAP-GPSK for the integrated EAP server
config HOSTAPD_EAP_GPSK_SHA256
bool
prompt "Include support for optional SHA256 cipher suite in EAP-GPSK"
help
Include support for optional SHA256 cipher suite in EAP-GPSK
config HOSTAPD_EAP_FAST
bool
prompt "EAP-FAST for the integrated EAP server"
help
EAP-FAST for the integrated EAP server
Note: Default OpenSSL package does not include support for all the
functionality needed for EAP-FAST. If EAP-FAST is enabled with
OpenSSL,
the OpenSSL library must be patched
(openssl-0.9.9-session-ticket.patch)
to add the needed functions.
config HOSTAPD_WPS
bool
prompt "Wi-Fi Protected Setup (WPS)"
help
Wi-Fi Protected Setup (WPS)
config HOSTAPD_WPS2
bool
prompt "Enable WSC 2.0 support"
help
Enable WSC 2.0 support
config HOSTAPD_WPS_UPNP
bool
prompt "Enable UPnP support for external WPS Registrars"
help
Enable UPnP support for external WPS Registrars
config HOSTAPD_WPS_NFC
bool
prompt "Enable WPS support with NFC config method"
help
Enable WPS support with NFC config method
config HOSTAPD_EAP_IKEV2
bool
prompt "EAP-IKEv2"
help
EAP-IKEv2
config HOSTAPD_EAP_TNC
bool
prompt "Trusted Network Connect (EAP-TNC)"
help
Trusted Network Connect (EAP-TNC)
config HOSTAPD_PKCS12
bool
prompt "PKCS#12 (PFX) support"
help
PKCS#12 (PFX) support (used to read private key and certificate
file from
a file that usually has extension .p12 or .pfx)
config HOSTAPD_RADIUS_SERVER
bool
prompt "RADIUS authentication server"
help
RADIUS authentication server. This provides access to the
integrated EAP
server from external hosts using RADIUS.
config HOSTAPD_IPV6
bool
prompt "Build IPv6 support for RADIUS operations"
help
Build IPv6 support for RADIUS operations
config HOSTAPD_IEEE80211R
bool
prompt "IEEE Std 802.11r-2008 (Fast BSS Transition)"
help
IEEE Std 802.11r-2008 (Fast BSS Transition)
config HOSTAPD_DRIVER_RADIUS_ACL
bool
prompt "Hostapd's IEEE 802.11 authentication (ACL)"
help
Use the hostapd's IEEE 802.11 authentication (ACL), but without
the IEEE 802.11 Management capability (e.g., madwifi or
FreeBSD/net80211)
config HOSTAPD_IEEE80211N
bool
prompt "IEEE 802.11n (High Throughput) support"
help
IEEE 802.11n (High Throughput) support
config HOSTAPD_WNM
bool
prompt "Wireless Network Management (IEEE Std 802.11v-2011)
(EXPERIMENTAL)"
help
Wireless Network Management (IEEE Std 802.11v-2011)
Note: This is experimental and not complete implementation.
config HOSTAPD_IEEE80211AC
bool
prompt "IEEE 802.11ac (Very High Throughput) support"
help
IEEE 802.11ac (Very High Throughput) support
config HOSTAPD_NO_STDOUT_DEBUG
bool
prompt "Remove stdout debugging code"
help
Remove debugging code that is printing out debug messages to stdout.
This can be used to reduce the size of the hostapd considerably if
debugging
code is not needed.
config HOSTAPD_DEBUG_FILE
bool
prompt "Log file support"
help
Add support for writing debug log to a file: -f /tmp/hostapd.log
Disabled by default.
config HOSTAPD_NO_ACCOUNTING
bool
prompt "Remove support for RADIUS accounting"
help
Remove support for RADIUS accounting
config HOSTAPD_NO_RADIUS
bool
prompt "Remove support for RADIUS"
help
Remove support for RADIUS
config HOSTAPD_NO_VLAN
bool
prompt "Remove support for VLANs"
help
Remove support for VLANs
config HOSTAPD_FULL_DYNAMIC_VLAN
bool
prompt "Fully dynamic VLAN support"
help
Enable support for fully dynamic VLANs. This enables hostapd to
automatically create bridge and VLAN interfaces if necessary.
config HOSTAPD_VLAN_NETLINK
bool
prompt "netlink-based kernel API for VLAN operations"
help
Use netlink-based kernel API for VLAN operations instead of ioctl()
Note: This requires libnl 3.1 or newer.
config HOSTAPD_NO_DUMP_STATE
bool
prompt "Remove SIGUSR1 state dump support"
help
Remove support for dumping state into a file on SIGUSR1 signal
This can be used to reduce binary size at the cost of disabling a
debugging
option.
config HOSTAPD_WPA_TRACE
bool
prompt "Enable tracing code for developer debugging"
help
Enable tracing code for developer debugging
This tracks use of memory allocations and other registrations and
reports
incorrect use with a backtrace of call (or allocation) location.
config HOSTAPD_NO_RANDOM_POOL
bool
prompt "Disabled hostapd's internal random pool"
help
hostapd depends on strong random number generation being available
from the
operating system. os_get_random() function is used to fetch random
data when
needed, e.g., for key generation. On Linux and BSD systems, this
works by
reading /dev/urandom. It should be noted that the OS entropy pool
needs to be
properly initialized before hostapd is started. This is important
especially
on embedded devices that do not have a hardware random number
generator and
may by default start up with minimal entropy available for random
number
generation.
As a safety net, hostapd is by default trying to internally collect
additional entropy for generating random data to mix in with the
data
fetched from the OS. This by itself is not considered to be very
strong, but
it may help in cases where the system pool is not initialized
properly.
However, it is very strongly recommended that the system pool is
initialized
with enough entropy either by using hardware assisted random number
generator or by storing state over device reboots.
hostapd can be configured to maintain its own entropy store over
restarts to
enhance random number generation. This is not perfect, but it is
much more
secure than using the same sequence of random numbers after every
reboot.
This can be enabled with -e<entropy file> command line option. The
specified
file needs to be readable and writable by hostapd.
If the os_get_random() is known to provide strong random data
(e.g., on
Linux/BSD, the board in question is known to have reliable source
of random
data from /dev/urandom), the internal hostapd random pool can be
disabled.
This will save some in binary size and CPU use. However, this
should only be
considered for builds that are known to be used on devices that
meet the
requirements described above.
#config HOSTAPD_TLS
#string
#prompt "Select TLS implementation"
#default "openssl"
#help
# Select TLS implementation
# openssl = OpenSSL (default)
# gnutls = GnuTLS
#internal = Internal TLSv1 implementation (experimental)
# none = Empty template
config HOSTAPD_TLSV11
bool
prompt "TLS v1.1"
help
TLS-based EAP methods require at least TLS v1.0. Newer version of
TLS (v1.1)
can be enabled to get a stronger construction of messages when
block ciphers
are used.
config HOSTAPD_TLSV12
bool
prompt "TLS v1.2"
help
TLS-based EAP methods require at least TLS v1.0. Newer version of
TLS (v1.2)
can be enabled to enable use of stronger crypto algorithms.
config HOSTAPD_INTERNAL_LIBTOMMATH_FAST
bool
prompt "Internal LibTomMath"
help
At the cost of about 4 kB of additional binary size, the internal
LibTomMath
can be configured to include faster routines for exptmod, sqr, and
div to
speed up DH and RSA calculation considerably
config HOSTAPD_INTERWORKING
bool
prompt "Interworking (IEEE 802.11u)"
help
Interworking (IEEE 802.11u)
This can be used to enable functionality to improve interworking
with
external networks.
config HOSTAPD_HS20
bool
prompt "Hotspot 2.0"
help
Hotspot 2.0
config HOSTAPD_SQLITE
bool
prompt "SQLite database support"
help
Enable SQLite database support in hlr_auc_gw, EAP-SIM DB, and
eap_user_file
endif
*hostapd.make: *
# -*-makefile-*-
#
# Copyright (C) 2013 by Matthias Fend <matthias.fend@wolfvision.com>
#
# See CREDITS for details about who has contributed to this project.
#
# For further information about the PTXdist project and license conditions
# see the README file.
#
#
# We provide this package
#
PACKAGES-$(PTXCONF_HOSTAPD) += hostapd
#
# Paths and names
#
HOSTAPD_NAME := hostapd
HOSTAPD_VERSION := 2.0
HOSTAPD_MD5 := ba22e639bc57aa4035d2ea8ffa9bbbee
HOSTAPD := $(HOSTAPD_NAME)-$(HOSTAPD_VERSION)
HOSTAPD_SUFFIX := tar.gz
HOSTAPD_URL := http://w1.fi/releases/$(HOSTAPD).$(HOSTAPD_SUFFIX)
HOSTAPD_SOURCE := $(SRCDIR)/$(HOSTAPD).$(HOSTAPD_SUFFIX)
HOSTAPD_DIR := $(BUILDDIR)/$(HOSTAPD)
HOSTAPD_SUBDIR := $(HOSTAPD_NAME)
HOSTAPD_CONFIG := $(BUILDDIR)/$(HOSTAPD)/$(HOSTAPD_SUBDIR)/.config
HOSTAPD_LICENSE := BSD
#
----------------------------------------------------------------------------
# Prepare
#
----------------------------------------------------------------------------
HOSTAPD_PATH := PATH=$(CROSS_PATH)
#HOSTAPD_CONF_TOOL := NO
HOSTAPD_MAKE_ENV := \
$(CROSS_ENV) \
LIBDIR=/lib \
BINDIR=/sbin
$(STATEDIR)/hostapd.prepare:
@$(call targetinfo)
# # run 'make clean' as hostapd's build system does not recognize
config changes
@-cd $(HOSTAPD_DIR)/$(HOSTAPD_SUBDIR) && \
$(HOSTAPD_MAKE_ENV) $(HOSTAPD_PATH) $(MAKE) clean
@echo "CC=$(CROSS_CC)" >
$(HOSTAPD_CONFIG) && \
echo "CFLAGS += -I$(PTXDIST_SYSROOT_TARGET)/include" >>
$(HOSTAPD_CONFIG) && \
echo "CFLAGS += -I$(PTXDIST_SYSROOT_TARGET)/usr/include" >>
$(HOSTAPD_CONFIG) && \
echo "LDFLAGS += -L$(PTXDIST_SYSROOT_TARGET)/lib" >>
$(HOSTAPD_CONFIG) && \
echo "LDFLAGS += -L$(PTXDIST_SYSROOT_TARGET)/usr/lib" >>
$(HOSTAPD_CONFIG)
@grep -e PTXCONF_HOSTAPD_ $(PTXDIST_PTXCONFIG) | \
sed -e 's/PTXCONF_HOSTAPD_/CONFIG_/g' -e 's/\"//g' >> $(HOSTAPD_CONFIG)
@$(call touch)
#
----------------------------------------------------------------------------
# Target-Install
#
----------------------------------------------------------------------------
$(STATEDIR)/hostapd.targetinstall:
@$(call targetinfo)
@$(call install_init, hostapd)
@$(call install_fixup, hostapd,PRIORITY,optional)
@$(call install_fixup, hostapd,SECTION,base)
@$(call install_fixup, hostapd,AUTHOR,"Matthias Fend <
matthias.fend@wolfvision.com>")
@$(call install_fixup, hostapd,DESCRIPTION,missing)
@$(call install_copy, hostapd, 0, 0, 0755,
$(HOSTAPD_DIR)/$(HOSTAPD_SUBDIR)/hostapd, /usr/bin/hostapd)
@$(call install_finish, hostapd)
@$(call touch)
#
----------------------------------------------------------------------------
# Clean
#
----------------------------------------------------------------------------
$(STATEDIR)/hostapd.clean:
@$(call targetinfo)
@-cd $(HOSTAPD_DIR) && \
$(HOSTAPD_ENV) $(HOSTAPD_PATH) $(MAKE) clean
@$(call clean_pkg, HOSTAPD)
# vim: syntax=make
2013/5/7 Matthias Fend <Matthias.Fend@wolfvision.net>
> Hi Pascal,
>
> > Von: ptxdist-bounces@pengutronix.de [mailto:
> ptxdist-bounces@pengutronix.de] Im Auftrag von Pascal K
> > Gesendet: Dienstag, 07. Mai 2013 10:18
> > An: ptxdist@pengutronix.de
> > Betreff: [ptxdist] Building hostapd for PTXdist and an ARM Target
> >
> > Hello all,
> >
> > I'am beginning to use PTXdist, so I followed the How to become a PTXdist
> Guru Manual to get started.
> > But there is some information which I don't find/don't get.
> >
> > My task:
> > -> Building hostapd-2.0.tar.gz for my ARM Cortex A8 target board
> >
> > So I tried to follow section 4.2.2 in the manual.
> >
> > $ ptxdist newpackage target
> > edited the mandatory fields, added md5sum, selected the package in
> > $ ptxdist menuconfig
> > $ ptxdist get hostapd
> > $ ptxdist extract hostapd
> > $ ptxdist prepare hostapd
> > and finally tried edited inside the hostapd folder the defconfig file to
> .config
> > $ ptxdist compile hostapd
> >
> > now gives me the error that
> >
> > make[1]: Entering directory
> `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> > make[1]: *** No targets specified and no makefile found. Stop.
> > make[1]: Leaving directory
> `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> > make: ***
> [/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/state/hostapd.compile]
> Error 2
> >
> >
> > So I think I missed a step or a went with the wrong option at the
> beginning.
> > Could someone give me an advice, that would be great!
> >
> >
> > Best regards,
> > Pascal
>
> Here comes a patch which will add hostapd-2.0 to ptxdist. It's not yet
> finished and (most) probably not everything is working.
> But maybe you can use it as starting point...
>
> good luck,
> ~matthias
>
> ---
> rules/hostapd.in | 411
> ++++++++++++++++++++++++++++++++++++++++++++++++++++
> rules/hostapd.make | 89 +++++++++++
> 2 files changed, 500 insertions(+), 0 deletions(-)
> create mode 100644 rules/hostapd.in
> create mode 100644 rules/hostapd.make
>
> diff --git a/rules/hostapd.in b/rules/hostapd.in
> new file mode 100644
> index 0000000..78bef61
> --- /dev/null
> +++ b/rules/hostapd.in
> @@ -0,0 +1,411 @@
> +## SECTION=networking
> +
> +config HOSTAPD
> + bool
> + prompt "hostapd"
> + help
> + FIXME
> +
> +if HOSTAPD
> +
> + config HOSTAPD_DRIVER_HOSTAP
> + bool
> + prompt "HOSTAP driver"
> + help
> + Driver interface for Host AP driver
> +
> + config HOSTAPD_DRIVER_WIRED
> + bool
> + prompt "Wired driver"
> + help
> + Driver interface for wired authenticator
> +
> + config HOSTAPD_DRIVER_NL80211
> + bool
> + prompt "NL80211 driver"
> + select LIBNL
> + help
> + Driver interface for drivers using the nl80211 kernel interface
> +
> + config HOSTAPD_DRIVER_NONE
> + bool
> + prompt "no driver"
> + help
> + Driver interface for no driver (e.g., RADIUS server only)
> +
> + config HOSTAPD_IAPP
> + bool
> + prompt "IEEE 802.11F/IAPP"
> + help
> + IEEE 802.11F/IAPP
> +
> + config HOSTAPD_RSN_PREAUTH
> + bool
> + prompt "WPA2/IEEE 802.11i RSN pre-authentication"
> + help
> + WPA2/IEEE 802.11i RSN pre-authentication
> +
> + config HOSTAPD_PEERKEY
> + bool
> + prompt "PeerKey handshake for Station to Station Link (IEEE
> 802.11e DLS)"
> + help
> + PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
> +
> + config HOSTAPD_IEEE80211W
> + bool
> + prompt "IEEE 802.11w (management frame protection)"
> + help
> + IEEE 802.11w (management frame protection)
> + This version is an experimental implementation based on IEEE
> 802.11w/D1.0
> + draft and is subject to change since the standard has not yet
> been finalized.
> + Driver support is also needed for IEEE 802.11w.
> +
> + config HOSTAPD_EAP
> + bool
> + prompt "Integrated EAP server"
> + help
> + Integrated EAP server
> +
> + config HOSTAPD_EAP_MD5
> + bool
> + prompt "EAP-MD5 for the integrated EAP server"
> + help
> + EAP-MD5 for the integrated EAP server
> +
> + config HOSTAPD_EAP_TLS
> + bool
> + prompt "EAP-TLS for the integrated EAP server"
> + help
> + EAP-TLS for the integrated EAP server
> +
> + config HOSTAPD_EAP_MSCHAPV2
> + bool
> + prompt "EAP-MSCHAPv2 for the integrated EAP server"
> + help
> + EAP-MSCHAPv2 for the integrated EAP server
> +
> + config HOSTAPD_EAP_PEAP
> + bool
> + prompt "EAP-PEAP for the integrated EAP server"
> + help
> + EAP-PEAP for the integrated EAP server
> +
> + config HOSTAPD_EAP_GTC
> + bool
> + prompt "EAP-GTC for the integrated EAP server"
> + help
> + EAP-GTC for the integrated EAP server
> +
> + config HOSTAPD_EAP_TTLS
> + bool
> + prompt "EAP-TTLS for the integrated EAP server"
> + help
> + EAP-TTLS for the integrated EAP server
> +
> + config HOSTAPD_EAP_SIM
> + bool
> + prompt "EAP-SIM for the integrated EAP server"
> + help
> + EAP-SIM for the integrated EAP server
> +
> + config HOSTAPD_EAP_AKA
> + bool
> + prompt "EAP-AKA for the integrated EAP server"
> + help
> + EAP-AKA for the integrated EAP server
> +
> + config HOSTAPD_EAP_AKA_PRIME
> + bool
> + prompt "EAP-AKA' (AKA-Prime)"
> + help
> + EAP-AKA' (AKA-Prime) for the integrated EAP server
> + This requires CONFIG_EAP_AKA to be enabled, too.
> +
> + config HOSTAPD_EAP_PAX
> + bool
> + prompt "EAP-PAX for the integrated EAP server"
> + help
> + EAP-PAX for the integrated EAP server
> +
> + config HOSTAPD_EAP_PSK
> + bool
> + prompt "EAP-PSK for the integrated EAP server"
> + help
> + EAP-PSK for the integrated EAP server (this is _not_ needed for
> WPA-PSK)
> +
> + config HOSTAPD_EAP_PWD
> + bool
> + prompt "EAP-pwd for the integrated EAP server"
> + help
> + EAP-pwd for the integrated EAP server (secure authentication with
> a password)
> +
> + config HOSTAPD_EAP_SAKE
> + bool
> + prompt "EAP-SAKE for the integrated EAP server"
> + help
> + EAP-SAKE for the integrated EAP server
> +
> + config HOSTAPD_EAP_GPSK
> + bool
> + prompt "EAP-GPSK for the integrated EAP server"
> + help
> + EAP-GPSK for the integrated EAP server
> +
> + config HOSTAPD_EAP_GPSK_SHA256
> + bool
> + prompt "Include support for optional SHA256 cipher suite in
> EAP-GPSK"
> + help
> + Include support for optional SHA256 cipher suite in EAP-GPSK
> +
> + config HOSTAPD_EAP_FAST
> + bool
> + prompt "EAP-FAST for the integrated EAP server"
> + help
> + EAP-FAST for the integrated EAP server
> + Note: Default OpenSSL package does not include support for all the
> + functionality needed for EAP-FAST. If EAP-FAST is enabled with
> OpenSSL,
> + the OpenSSL library must be patched
> (openssl-0.9.9-session-ticket.patch)
> + to add the needed functions.
> +
> + config HOSTAPD_WPS
> + bool
> + prompt "Wi-Fi Protected Setup (WPS)"
> + help
> + Wi-Fi Protected Setup (WPS)
> +
> + config HOSTAPD_WPS2
> + bool
> + prompt "Enable WSC 2.0 support"
> + help
> + Enable WSC 2.0 support
> +
> + config HOSTAPD_WPS_UPNP
> + bool
> + prompt "Enable UPnP support for external WPS Registrars"
> + help
> + Enable UPnP support for external WPS Registrars
> +
> + config HOSTAPD_WPS_NFC
> + bool
> + prompt "Enable WPS support with NFC config method"
> + help
> + Enable WPS support with NFC config method
> +
> + config HOSTAPD_EAP_IKEV2
> + bool
> + prompt "EAP-IKEv2"
> + help
> + EAP-IKEv2
> +
> + config HOSTAPD_EAP_TNC
> + bool
> + prompt "Trusted Network Connect (EAP-TNC)"
> + help
> + Trusted Network Connect (EAP-TNC)
> +
> + config HOSTAPD_PKCS12
> + bool
> + prompt "PKCS#12 (PFX) support"
> + help
> + PKCS#12 (PFX) support (used to read private key and certificate
> file from
> + a file that usually has extension .p12 or .pfx)
> +
> + config HOSTAPD_RADIUS_SERVER
> + bool
> + prompt "RADIUS authentication server"
> + help
> + RADIUS authentication server. This provides access to the
> integrated EAP
> + server from external hosts using RADIUS.
> +
> + config HOSTAPD_IPV6
> + bool
> + prompt "Build IPv6 support for RADIUS operations"
> + help
> + Build IPv6 support for RADIUS operations
> +
> + config HOSTAPD_IEEE80211R
> + bool
> + prompt "IEEE Std 802.11r-2008 (Fast BSS Transition)"
> + help
> + IEEE Std 802.11r-2008 (Fast BSS Transition)
> +
> + config HOSTAPD_DRIVER_RADIUS_ACL
> + bool
> + prompt "Hostapd's IEEE 802.11 authentication (ACL)"
> + help
> + Use the hostapd's IEEE 802.11 authentication (ACL), but without
> + the IEEE 802.11 Management capability (e.g., madwifi or
> FreeBSD/net80211)
> +
> + config HOSTAPD_IEEE80211N
> + bool
> + prompt "IEEE 802.11n (High Throughput) support"
> + help
> + IEEE 802.11n (High Throughput) support
> +
> + config HOSTAPD_WNM
> + bool
> + prompt "Wireless Network Management (IEEE Std 802.11v-2011)
> (EXPERIMENTAL)"
> + help
> + Wireless Network Management (IEEE Std 802.11v-2011)
> + Note: This is experimental and not complete implementation.
> +
> + config HOSTAPD_IEEE80211AC
> + bool
> + prompt "IEEE 802.11ac (Very High Throughput) support"
> + help
> + IEEE 802.11ac (Very High Throughput) support
> +
> + config HOSTAPD_NO_STDOUT_DEBUG
> + bool
> + prompt "Remove stdout debugging code"
> + help
> + Remove debugging code that is printing out debug messages to
> stdout.
> + This can be used to reduce the size of the hostapd considerably
> if debugging
> + code is not needed.
> +
> + config HOSTAPD_DEBUG_FILE
> + bool
> + prompt "Log file support"
> + help
> + Add support for writing debug log to a file: -f /tmp/hostapd.log
> + Disabled by default.
> +
> + config HOSTAPD_NO_ACCOUNTING
> + bool
> + prompt "Remove support for RADIUS accounting"
> + help
> + Remove support for RADIUS accounting
> +
> + config HOSTAPD_NO_RADIUS
> + bool
> + prompt "Remove support for RADIUS"
> + help
> + Remove support for RADIUS
> +
> + config HOSTAPD_NO_VLAN
> + bool
> + prompt "Remove support for VLANs"
> + help
> + Remove support for VLANs
> +
> + config HOSTAPD_FULL_DYNAMIC_VLAN
> + bool
> + prompt "Fully dynamic VLAN support"
> + help
> + Enable support for fully dynamic VLANs. This enables hostapd to
> + automatically create bridge and VLAN interfaces if necessary.
> +
> + config HOSTAPD_VLAN_NETLINK
> + bool
> + prompt "netlink-based kernel API for VLAN operations"
> + help
> + Use netlink-based kernel API for VLAN operations instead of
> ioctl()
> + Note: This requires libnl 3.1 or newer.
> +
> + config HOSTAPD_NO_DUMP_STATE
> + bool
> + prompt "Remove SIGUSR1 state dump support"
> + help
> + Remove support for dumping state into a file on SIGUSR1 signal
> + This can be used to reduce binary size at the cost of disabling a
> debugging
> + option.
> +
> + config HOSTAPD_WPA_TRACE
> + bool
> + prompt "Enable tracing code for developer debugging"
> + help
> + Enable tracing code for developer debugging
> + This tracks use of memory allocations and other registrations and
> reports
> + incorrect use with a backtrace of call (or allocation) location.
> +
> + config HOSTAPD_NO_RANDOM_POOL
> + bool
> + prompt "Disabled hostapd's internal random pool"
> + help
> + hostapd depends on strong random number generation being
> available from the
> + operating system. os_get_random() function is used to fetch
> random data when
> + needed, e.g., for key generation. On Linux and BSD systems, this
> works by
> + reading /dev/urandom. It should be noted that the OS entropy pool
> needs to be
> + properly initialized before hostapd is started. This is important
> especially
> + on embedded devices that do not have a hardware random number
> generator and
> + may by default start up with minimal entropy available for random
> number
> + generation.
> +
> + As a safety net, hostapd is by default trying to internally
> collect
> + additional entropy for generating random data to mix in with the
> data
> + fetched from the OS. This by itself is not considered to be very
> strong, but
> + it may help in cases where the system pool is not initialized
> properly.
> + However, it is very strongly recommended that the system pool is
> initialized
> + with enough entropy either by using hardware assisted random
> number
> + generator or by storing state over device reboots.
> +
> + hostapd can be configured to maintain its own entropy store over
> restarts to
> + enhance random number generation. This is not perfect, but it is
> much more
> + secure than using the same sequence of random numbers after every
> reboot.
> + This can be enabled with -e<entropy file> command line option.
> The specified
> + file needs to be readable and writable by hostapd.
> +
> + If the os_get_random() is known to provide strong random data
> (e.g., on
> + Linux/BSD, the board in question is known to have reliable source
> of random
> + data from /dev/urandom), the internal hostapd random pool can be
> disabled.
> + This will save some in binary size and CPU use. However, this
> should only be
> + considered for builds that are known to be used on devices that
> meet the
> + requirements described above.
> +
> + config HOSTAPD_TLS
> + string
> + prompt "Select TLS implementation"
> + default "openssl"
> + help
> + Select TLS implementation
> + openssl = OpenSSL (default)
> + gnutls = GnuTLS
> + internal = Internal TLSv1 implementation (experimental)
> + none = Empty template
> +
> + config HOSTAPD_TLSV11
> + bool
> + prompt "TLS v1.1"
> + help
> + TLS-based EAP methods require at least TLS v1.0. Newer version of
> TLS (v1.1)
> + can be enabled to get a stronger construction of messages when
> block ciphers
> + are used.
> +
> + config HOSTAPD_TLSV12
> + bool
> + prompt "TLS v1.2"
> + help
> + TLS-based EAP methods require at least TLS v1.0. Newer version of
> TLS (v1.2)
> + can be enabled to enable use of stronger crypto algorithms.
> +
> + config HOSTAPD_INTERNAL_LIBTOMMATH_FAST
> + bool
> + prompt "Internal LibTomMath"
> + help
> + At the cost of about 4 kB of additional binary size, the internal
> LibTomMath
> + can be configured to include faster routines for exptmod, sqr,
> and div to
> + speed up DH and RSA calculation considerably
> +
> + config HOSTAPD_INTERWORKING
> + bool
> + prompt "Interworking (IEEE 802.11u)"
> + help
> + Interworking (IEEE 802.11u)
> + This can be used to enable functionality to improve interworking
> with
> + external networks.
> +
> + config HOSTAPD_HS20
> + bool
> + prompt "Hotspot 2.0"
> + help
> + Hotspot 2.0
> +
> + config HOSTAPD_SQLITE
> + bool
> + prompt "SQLite database support"
> + help
> + Enable SQLite database support in hlr_auc_gw, EAP-SIM DB, and
> eap_user_file
> +
> +endif
> +
> +
> diff --git a/rules/hostapd.make b/rules/hostapd.make
> new file mode 100644
> index 0000000..0ca5dd5
> --- /dev/null
> +++ b/rules/hostapd.make
> @@ -0,0 +1,89 @@
> +# -*-makefile-*-
> +#
> +# Copyright (C) 2013 by Matthias Fend <matthias.fend@wolfvision.com>
> +#
> +# See CREDITS for details about who has contributed to this project.
> +#
> +# For further information about the PTXdist project and license conditions
> +# see the README file.
> +#
> +
> +#
> +# We provide this package
> +#
> +PACKAGES-$(PTXCONF_HOSTAPD) += hostapd
> +
> +#
> +# Paths and names
> +#
> +HOSTAPD_NAME := hostapd
> +HOSTAPD_VERSION := 2.0
> +HOSTAPD_MD5 := ba22e639bc57aa4035d2ea8ffa9bbbee
> +HOSTAPD := $(HOSTAPD_NAME)-$(HOSTAPD_VERSION)
> +HOSTAPD_SUFFIX := tar.gz
> +HOSTAPD_URL := http://w1.fi/releases/$(HOSTAPD).$(HOSTAPD_SUFFIX)
> +HOSTAPD_SOURCE := $(SRCDIR)/$(HOSTAPD).$(HOSTAPD_SUFFIX)
> +HOSTAPD_DIR := $(BUILDDIR)/$(HOSTAPD)
> +HOSTAPD_SUBDIR := $(HOSTAPD_NAME)
> +HOSTAPD_CONFIG := $(BUILDDIR)/$(HOSTAPD)/$(HOSTAPD_SUBDIR)/.config
> +HOSTAPD_LICENSE := BSD
> +
> +#
> ----------------------------------------------------------------------------
> +# Prepare
> +#
> ----------------------------------------------------------------------------
> +
> +HOSTAPD_PATH := PATH=$(CROSS_PATH)
> +#HOSTAPD_CONF_TOOL := NO
> +HOSTAPD_MAKE_ENV := \
> + $(CROSS_ENV) \
> + LIBDIR=/lib \
> + BINDIR=/sbin
> +
> +
> +$(STATEDIR)/hostapd.prepare:
> + @$(call targetinfo)
> +# # run 'make clean' as hostapd's build system does not recognize
> config changes
> + @-cd $(HOSTAPD_DIR)/$(HOSTAPD_SUBDIR) && \
> + $(HOSTAPD_MAKE_ENV) $(HOSTAPD_PATH) $(MAKE) clean
> +
> + @echo "CC=$(CROSS_CC)" >
> $(HOSTAPD_CONFIG) && \
> + echo "CFLAGS += -I$(PTXDIST_SYSROOT_TARGET)/include" >>
> $(HOSTAPD_CONFIG) && \
> + echo "CFLAGS += -I$(PTXDIST_SYSROOT_TARGET)/usr/include" >>
> $(HOSTAPD_CONFIG) && \
> + echo "LDFLAGS += -L$(PTXDIST_SYSROOT_TARGET)/lib" >>
> $(HOSTAPD_CONFIG) && \
> + echo "LDFLAGS += -L$(PTXDIST_SYSROOT_TARGET)/usr/lib" >>
> $(HOSTAPD_CONFIG)
> +
> + @grep -e PTXCONF_HOSTAPD_ $(PTXDIST_PTXCONFIG) | \
> + sed -e 's/PTXCONF_HOSTAPD_/CONFIG_/g' -e 's/\"//g' >>
> $(HOSTAPD_CONFIG)
> +
> + @$(call touch)
> +
> +#
> ----------------------------------------------------------------------------
> +# Target-Install
> +#
> ----------------------------------------------------------------------------
> +
> +$(STATEDIR)/hostapd.targetinstall:
> + @$(call targetinfo)
> +
> + @$(call install_init, hostapd)
> + @$(call install_fixup, hostapd,PRIORITY,optional)
> + @$(call install_fixup, hostapd,SECTION,base)
> + @$(call install_fixup, hostapd,AUTHOR,"Matthias Fend <
> matthias.fend@wolfvision.com>")
> + @$(call install_fixup, hostapd,DESCRIPTION,missing)
> +
> + @$(call install_copy, hostapd, 0, 0, 0755,
> $(HOSTAPD_DIR)/$(HOSTAPD_SUBDIR)/hostapd, /usr/bin/hostapd)
> +
> + @$(call install_finish, hostapd)
> +
> + @$(call touch)
> +
> +#
> ----------------------------------------------------------------------------
> +# Clean
> +#
> ----------------------------------------------------------------------------
> +
> +$(STATEDIR)/hostapd.clean:
> + @$(call targetinfo)
> + @-cd $(HOSTAPD_DIR) && \
> + $(HOSTAPD_ENV) $(HOSTAPD_PATH) $(MAKE) clean
> + @$(call clean_pkg, HOSTAPD)
> +
> +# vim: syntax=make
> --
> 1.7.0.4
>
>
> --
> ptxdist mailing list
> ptxdist@pengutronix.de
>
[-- Attachment #1.2: Type: text/html, Size: 56980 bytes --]
[-- Attachment #2: Type: text/plain, Size: 48 bytes --]
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-06-28 16:08 ` irfan rafique
2013-07-01 6:45 ` Matthias Fend
@ 2013-07-01 7:14 ` Pascal K
1 sibling, 0 replies; 11+ messages in thread
From: Pascal K @ 2013-07-01 7:14 UTC (permalink / raw)
To: ptxdist
[-- Attachment #1.1: Type: text/plain, Size: 896 bytes --]
Hello Irfan,
i followed this guide for hostapd.config file creation
http://www.rpiblog.com/2012/12/turn-raspberry-pi-into-wireless-access.html
Are you sure that your driver supports the AP Mode?
Best regards,
Pascal
2013/6/28 irfan rafique <mir.kiel@gmail.com>
> Hi Matthias,
>
> I added your patch and tried to add package using
> following commands:
>
> $ptxdist newpackage target
> edited the mandatory fields, added md5sum
> $ptxdist menuconfig
> [*]hostapd
> $ptxdist go
>
> But on the target machine, i find only hostapd(binary file)
> but not hostapd.config file:
>
> /usr/bin/hostapd
> /usr/lib/ipkg/info/hostapd.control
> /usr/lib/ipkg/info/hostapd.list
>
> If i use $hostapd ./hostapd.config: it shows
> No drivers enabled.
>
> Please help me to sort out this problem.
>
> with Best Regards,
>
> Irfan Rafique
>
>
>
> --
> ptxdist mailing list
> ptxdist@pengutronix.de
>
[-- Attachment #1.2: Type: text/html, Size: 1621 bytes --]
[-- Attachment #2: Type: text/plain, Size: 48 bytes --]
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-06-28 16:08 ` irfan rafique
@ 2013-07-01 6:45 ` Matthias Fend
2013-07-01 7:14 ` Pascal K
1 sibling, 0 replies; 11+ messages in thread
From: Matthias Fend @ 2013-07-01 6:45 UTC (permalink / raw)
To: ptxdist
Hi Irfan,
> -----Ursprüngliche Nachricht-----
> Von: ptxdist-bounces@pengutronix.de [mailto:ptxdist-
> bounces@pengutronix.de] Im Auftrag von irfan rafique
> Gesendet: Freitag, 28. Juni 2013 18:09
> An: ptxdist@pengutronix.de
> Betreff: Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
>
> Hi Matthias,
>
> I added your patch and tried to add package using following commands:
>
> $ptxdist newpackage target
> edited the mandatory fields, added md5sum $ptxdist menuconfig
> [*]hostapd
> $ptxdist go
>
> But on the target machine, i find only hostapd(binary file) but not
> hostapd.config file:
>
> /usr/bin/hostapd
> /usr/lib/ipkg/info/hostapd.control
> /usr/lib/ipkg/info/hostapd.list
True. The patch only installs the binary.
You can modify the patch that a configuration file will be installed.
Of course you also can use different other ways to bring the configuration file to you sysroot (generating at runtime, separate rule file, ...)
>
> If i use $hostapd ./hostapd.config: it shows No drivers enabled.
Did you enable a driver interface in the ptxdist hostapd configuration (e.g. NL80211) ?
~Matthias
>
> Please help me to sort out this problem.
>
> with Best Regards,
>
> Irfan Rafique
>
>
>
> --
> ptxdist mailing list
> ptxdist@pengutronix.de
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:57 ` Matthias Fend
@ 2013-06-28 16:08 ` irfan rafique
2013-07-01 6:45 ` Matthias Fend
2013-07-01 7:14 ` Pascal K
0 siblings, 2 replies; 11+ messages in thread
From: irfan rafique @ 2013-06-28 16:08 UTC (permalink / raw)
To: ptxdist
Hi Matthias,
I added your patch and tried to add package using
following commands:
$ptxdist newpackage target
edited the mandatory fields, added md5sum
$ptxdist menuconfig
[*]hostapd
$ptxdist go
But on the target machine, i find only hostapd(binary file)
but not hostapd.config file:
/usr/bin/hostapd
/usr/lib/ipkg/info/hostapd.control
/usr/lib/ipkg/info/hostapd.list
If i use $hostapd ./hostapd.config: it shows
No drivers enabled.
Please help me to sort out this problem.
with Best Regards,
Irfan Rafique
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:17 Pascal K
2013-05-07 8:28 ` Juergen Beisert
2013-05-07 8:34 ` Josef Holzmayr
@ 2013-05-07 8:57 ` Matthias Fend
2013-06-28 16:08 ` irfan rafique
2 siblings, 1 reply; 11+ messages in thread
From: Matthias Fend @ 2013-05-07 8:57 UTC (permalink / raw)
To: ptxdist
Hi Pascal,
> Von: ptxdist-bounces@pengutronix.de [mailto:ptxdist-bounces@pengutronix.de] Im Auftrag von Pascal K
> Gesendet: Dienstag, 07. Mai 2013 10:18
> An: ptxdist@pengutronix.de
> Betreff: [ptxdist] Building hostapd for PTXdist and an ARM Target
>
> Hello all,
>
> I'am beginning to use PTXdist, so I followed the How to become a PTXdist Guru Manual to get started.
> But there is some information which I don't find/don't get.
>
> My task:
> -> Building hostapd-2.0.tar.gz for my ARM Cortex A8 target board
>
> So I tried to follow section 4.2.2 in the manual.
>
> $ ptxdist newpackage target
> edited the mandatory fields, added md5sum, selected the package in
> $ ptxdist menuconfig
> $ ptxdist get hostapd
> $ ptxdist extract hostapd
> $ ptxdist prepare hostapd
> and finally tried edited inside the hostapd folder the defconfig file to .config
> $ ptxdist compile hostapd
>
> now gives me the error that
>
> make[1]: Entering directory `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> make[1]: *** No targets specified and no makefile found. Stop.
> make[1]: Leaving directory `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> make: *** [/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/state/hostapd.compile] Error 2
>
>
> So I think I missed a step or a went with the wrong option at the beginning.
> Could someone give me an advice, that would be great!
>
>
> Best regards,
> Pascal
Here comes a patch which will add hostapd-2.0 to ptxdist. It's not yet finished and (most) probably not everything is working.
But maybe you can use it as starting point...
good luck,
~matthias
---
rules/hostapd.in | 411 ++++++++++++++++++++++++++++++++++++++++++++++++++++
rules/hostapd.make | 89 +++++++++++
2 files changed, 500 insertions(+), 0 deletions(-)
create mode 100644 rules/hostapd.in
create mode 100644 rules/hostapd.make
diff --git a/rules/hostapd.in b/rules/hostapd.in
new file mode 100644
index 0000000..78bef61
--- /dev/null
+++ b/rules/hostapd.in
@@ -0,0 +1,411 @@
+## SECTION=networking
+
+config HOSTAPD
+ bool
+ prompt "hostapd"
+ help
+ FIXME
+
+if HOSTAPD
+
+ config HOSTAPD_DRIVER_HOSTAP
+ bool
+ prompt "HOSTAP driver"
+ help
+ Driver interface for Host AP driver
+
+ config HOSTAPD_DRIVER_WIRED
+ bool
+ prompt "Wired driver"
+ help
+ Driver interface for wired authenticator
+
+ config HOSTAPD_DRIVER_NL80211
+ bool
+ prompt "NL80211 driver"
+ select LIBNL
+ help
+ Driver interface for drivers using the nl80211 kernel interface
+
+ config HOSTAPD_DRIVER_NONE
+ bool
+ prompt "no driver"
+ help
+ Driver interface for no driver (e.g., RADIUS server only)
+
+ config HOSTAPD_IAPP
+ bool
+ prompt "IEEE 802.11F/IAPP"
+ help
+ IEEE 802.11F/IAPP
+
+ config HOSTAPD_RSN_PREAUTH
+ bool
+ prompt "WPA2/IEEE 802.11i RSN pre-authentication"
+ help
+ WPA2/IEEE 802.11i RSN pre-authentication
+
+ config HOSTAPD_PEERKEY
+ bool
+ prompt "PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)"
+ help
+ PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
+
+ config HOSTAPD_IEEE80211W
+ bool
+ prompt "IEEE 802.11w (management frame protection)"
+ help
+ IEEE 802.11w (management frame protection)
+ This version is an experimental implementation based on IEEE 802.11w/D1.0
+ draft and is subject to change since the standard has not yet been finalized.
+ Driver support is also needed for IEEE 802.11w.
+
+ config HOSTAPD_EAP
+ bool
+ prompt "Integrated EAP server"
+ help
+ Integrated EAP server
+
+ config HOSTAPD_EAP_MD5
+ bool
+ prompt "EAP-MD5 for the integrated EAP server"
+ help
+ EAP-MD5 for the integrated EAP server
+
+ config HOSTAPD_EAP_TLS
+ bool
+ prompt "EAP-TLS for the integrated EAP server"
+ help
+ EAP-TLS for the integrated EAP server
+
+ config HOSTAPD_EAP_MSCHAPV2
+ bool
+ prompt "EAP-MSCHAPv2 for the integrated EAP server"
+ help
+ EAP-MSCHAPv2 for the integrated EAP server
+
+ config HOSTAPD_EAP_PEAP
+ bool
+ prompt "EAP-PEAP for the integrated EAP server"
+ help
+ EAP-PEAP for the integrated EAP server
+
+ config HOSTAPD_EAP_GTC
+ bool
+ prompt "EAP-GTC for the integrated EAP server"
+ help
+ EAP-GTC for the integrated EAP server
+
+ config HOSTAPD_EAP_TTLS
+ bool
+ prompt "EAP-TTLS for the integrated EAP server"
+ help
+ EAP-TTLS for the integrated EAP server
+
+ config HOSTAPD_EAP_SIM
+ bool
+ prompt "EAP-SIM for the integrated EAP server"
+ help
+ EAP-SIM for the integrated EAP server
+
+ config HOSTAPD_EAP_AKA
+ bool
+ prompt "EAP-AKA for the integrated EAP server"
+ help
+ EAP-AKA for the integrated EAP server
+
+ config HOSTAPD_EAP_AKA_PRIME
+ bool
+ prompt "EAP-AKA' (AKA-Prime)"
+ help
+ EAP-AKA' (AKA-Prime) for the integrated EAP server
+ This requires CONFIG_EAP_AKA to be enabled, too.
+
+ config HOSTAPD_EAP_PAX
+ bool
+ prompt "EAP-PAX for the integrated EAP server"
+ help
+ EAP-PAX for the integrated EAP server
+
+ config HOSTAPD_EAP_PSK
+ bool
+ prompt "EAP-PSK for the integrated EAP server"
+ help
+ EAP-PSK for the integrated EAP server (this is _not_ needed for WPA-PSK)
+
+ config HOSTAPD_EAP_PWD
+ bool
+ prompt "EAP-pwd for the integrated EAP server"
+ help
+ EAP-pwd for the integrated EAP server (secure authentication with a password)
+
+ config HOSTAPD_EAP_SAKE
+ bool
+ prompt "EAP-SAKE for the integrated EAP server"
+ help
+ EAP-SAKE for the integrated EAP server
+
+ config HOSTAPD_EAP_GPSK
+ bool
+ prompt "EAP-GPSK for the integrated EAP server"
+ help
+ EAP-GPSK for the integrated EAP server
+
+ config HOSTAPD_EAP_GPSK_SHA256
+ bool
+ prompt "Include support for optional SHA256 cipher suite in EAP-GPSK"
+ help
+ Include support for optional SHA256 cipher suite in EAP-GPSK
+
+ config HOSTAPD_EAP_FAST
+ bool
+ prompt "EAP-FAST for the integrated EAP server"
+ help
+ EAP-FAST for the integrated EAP server
+ Note: Default OpenSSL package does not include support for all the
+ functionality needed for EAP-FAST. If EAP-FAST is enabled with OpenSSL,
+ the OpenSSL library must be patched (openssl-0.9.9-session-ticket.patch)
+ to add the needed functions.
+
+ config HOSTAPD_WPS
+ bool
+ prompt "Wi-Fi Protected Setup (WPS)"
+ help
+ Wi-Fi Protected Setup (WPS)
+
+ config HOSTAPD_WPS2
+ bool
+ prompt "Enable WSC 2.0 support"
+ help
+ Enable WSC 2.0 support
+
+ config HOSTAPD_WPS_UPNP
+ bool
+ prompt "Enable UPnP support for external WPS Registrars"
+ help
+ Enable UPnP support for external WPS Registrars
+
+ config HOSTAPD_WPS_NFC
+ bool
+ prompt "Enable WPS support with NFC config method"
+ help
+ Enable WPS support with NFC config method
+
+ config HOSTAPD_EAP_IKEV2
+ bool
+ prompt "EAP-IKEv2"
+ help
+ EAP-IKEv2
+
+ config HOSTAPD_EAP_TNC
+ bool
+ prompt "Trusted Network Connect (EAP-TNC)"
+ help
+ Trusted Network Connect (EAP-TNC)
+
+ config HOSTAPD_PKCS12
+ bool
+ prompt "PKCS#12 (PFX) support"
+ help
+ PKCS#12 (PFX) support (used to read private key and certificate file from
+ a file that usually has extension .p12 or .pfx)
+
+ config HOSTAPD_RADIUS_SERVER
+ bool
+ prompt "RADIUS authentication server"
+ help
+ RADIUS authentication server. This provides access to the integrated EAP
+ server from external hosts using RADIUS.
+
+ config HOSTAPD_IPV6
+ bool
+ prompt "Build IPv6 support for RADIUS operations"
+ help
+ Build IPv6 support for RADIUS operations
+
+ config HOSTAPD_IEEE80211R
+ bool
+ prompt "IEEE Std 802.11r-2008 (Fast BSS Transition)"
+ help
+ IEEE Std 802.11r-2008 (Fast BSS Transition)
+
+ config HOSTAPD_DRIVER_RADIUS_ACL
+ bool
+ prompt "Hostapd's IEEE 802.11 authentication (ACL)"
+ help
+ Use the hostapd's IEEE 802.11 authentication (ACL), but without
+ the IEEE 802.11 Management capability (e.g., madwifi or FreeBSD/net80211)
+
+ config HOSTAPD_IEEE80211N
+ bool
+ prompt "IEEE 802.11n (High Throughput) support"
+ help
+ IEEE 802.11n (High Throughput) support
+
+ config HOSTAPD_WNM
+ bool
+ prompt "Wireless Network Management (IEEE Std 802.11v-2011) (EXPERIMENTAL)"
+ help
+ Wireless Network Management (IEEE Std 802.11v-2011)
+ Note: This is experimental and not complete implementation.
+
+ config HOSTAPD_IEEE80211AC
+ bool
+ prompt "IEEE 802.11ac (Very High Throughput) support"
+ help
+ IEEE 802.11ac (Very High Throughput) support
+
+ config HOSTAPD_NO_STDOUT_DEBUG
+ bool
+ prompt "Remove stdout debugging code"
+ help
+ Remove debugging code that is printing out debug messages to stdout.
+ This can be used to reduce the size of the hostapd considerably if debugging
+ code is not needed.
+
+ config HOSTAPD_DEBUG_FILE
+ bool
+ prompt "Log file support"
+ help
+ Add support for writing debug log to a file: -f /tmp/hostapd.log
+ Disabled by default.
+
+ config HOSTAPD_NO_ACCOUNTING
+ bool
+ prompt "Remove support for RADIUS accounting"
+ help
+ Remove support for RADIUS accounting
+
+ config HOSTAPD_NO_RADIUS
+ bool
+ prompt "Remove support for RADIUS"
+ help
+ Remove support for RADIUS
+
+ config HOSTAPD_NO_VLAN
+ bool
+ prompt "Remove support for VLANs"
+ help
+ Remove support for VLANs
+
+ config HOSTAPD_FULL_DYNAMIC_VLAN
+ bool
+ prompt "Fully dynamic VLAN support"
+ help
+ Enable support for fully dynamic VLANs. This enables hostapd to
+ automatically create bridge and VLAN interfaces if necessary.
+
+ config HOSTAPD_VLAN_NETLINK
+ bool
+ prompt "netlink-based kernel API for VLAN operations"
+ help
+ Use netlink-based kernel API for VLAN operations instead of ioctl()
+ Note: This requires libnl 3.1 or newer.
+
+ config HOSTAPD_NO_DUMP_STATE
+ bool
+ prompt "Remove SIGUSR1 state dump support"
+ help
+ Remove support for dumping state into a file on SIGUSR1 signal
+ This can be used to reduce binary size at the cost of disabling a debugging
+ option.
+
+ config HOSTAPD_WPA_TRACE
+ bool
+ prompt "Enable tracing code for developer debugging"
+ help
+ Enable tracing code for developer debugging
+ This tracks use of memory allocations and other registrations and reports
+ incorrect use with a backtrace of call (or allocation) location.
+
+ config HOSTAPD_NO_RANDOM_POOL
+ bool
+ prompt "Disabled hostapd's internal random pool"
+ help
+ hostapd depends on strong random number generation being available from the
+ operating system. os_get_random() function is used to fetch random data when
+ needed, e.g., for key generation. On Linux and BSD systems, this works by
+ reading /dev/urandom. It should be noted that the OS entropy pool needs to be
+ properly initialized before hostapd is started. This is important especially
+ on embedded devices that do not have a hardware random number generator and
+ may by default start up with minimal entropy available for random number
+ generation.
+
+ As a safety net, hostapd is by default trying to internally collect
+ additional entropy for generating random data to mix in with the data
+ fetched from the OS. This by itself is not considered to be very strong, but
+ it may help in cases where the system pool is not initialized properly.
+ However, it is very strongly recommended that the system pool is initialized
+ with enough entropy either by using hardware assisted random number
+ generator or by storing state over device reboots.
+
+ hostapd can be configured to maintain its own entropy store over restarts to
+ enhance random number generation. This is not perfect, but it is much more
+ secure than using the same sequence of random numbers after every reboot.
+ This can be enabled with -e<entropy file> command line option. The specified
+ file needs to be readable and writable by hostapd.
+
+ If the os_get_random() is known to provide strong random data (e.g., on
+ Linux/BSD, the board in question is known to have reliable source of random
+ data from /dev/urandom), the internal hostapd random pool can be disabled.
+ This will save some in binary size and CPU use. However, this should only be
+ considered for builds that are known to be used on devices that meet the
+ requirements described above.
+
+ config HOSTAPD_TLS
+ string
+ prompt "Select TLS implementation"
+ default "openssl"
+ help
+ Select TLS implementation
+ openssl = OpenSSL (default)
+ gnutls = GnuTLS
+ internal = Internal TLSv1 implementation (experimental)
+ none = Empty template
+
+ config HOSTAPD_TLSV11
+ bool
+ prompt "TLS v1.1"
+ help
+ TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.1)
+ can be enabled to get a stronger construction of messages when block ciphers
+ are used.
+
+ config HOSTAPD_TLSV12
+ bool
+ prompt "TLS v1.2"
+ help
+ TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.2)
+ can be enabled to enable use of stronger crypto algorithms.
+
+ config HOSTAPD_INTERNAL_LIBTOMMATH_FAST
+ bool
+ prompt "Internal LibTomMath"
+ help
+ At the cost of about 4 kB of additional binary size, the internal LibTomMath
+ can be configured to include faster routines for exptmod, sqr, and div to
+ speed up DH and RSA calculation considerably
+
+ config HOSTAPD_INTERWORKING
+ bool
+ prompt "Interworking (IEEE 802.11u)"
+ help
+ Interworking (IEEE 802.11u)
+ This can be used to enable functionality to improve interworking with
+ external networks.
+
+ config HOSTAPD_HS20
+ bool
+ prompt "Hotspot 2.0"
+ help
+ Hotspot 2.0
+
+ config HOSTAPD_SQLITE
+ bool
+ prompt "SQLite database support"
+ help
+ Enable SQLite database support in hlr_auc_gw, EAP-SIM DB, and eap_user_file
+
+endif
+
+
diff --git a/rules/hostapd.make b/rules/hostapd.make
new file mode 100644
index 0000000..0ca5dd5
--- /dev/null
+++ b/rules/hostapd.make
@@ -0,0 +1,89 @@
+# -*-makefile-*-
+#
+# Copyright (C) 2013 by Matthias Fend <matthias.fend@wolfvision.com>
+#
+# See CREDITS for details about who has contributed to this project.
+#
+# For further information about the PTXdist project and license conditions
+# see the README file.
+#
+
+#
+# We provide this package
+#
+PACKAGES-$(PTXCONF_HOSTAPD) += hostapd
+
+#
+# Paths and names
+#
+HOSTAPD_NAME := hostapd
+HOSTAPD_VERSION := 2.0
+HOSTAPD_MD5 := ba22e639bc57aa4035d2ea8ffa9bbbee
+HOSTAPD := $(HOSTAPD_NAME)-$(HOSTAPD_VERSION)
+HOSTAPD_SUFFIX := tar.gz
+HOSTAPD_URL := http://w1.fi/releases/$(HOSTAPD).$(HOSTAPD_SUFFIX)
+HOSTAPD_SOURCE := $(SRCDIR)/$(HOSTAPD).$(HOSTAPD_SUFFIX)
+HOSTAPD_DIR := $(BUILDDIR)/$(HOSTAPD)
+HOSTAPD_SUBDIR := $(HOSTAPD_NAME)
+HOSTAPD_CONFIG := $(BUILDDIR)/$(HOSTAPD)/$(HOSTAPD_SUBDIR)/.config
+HOSTAPD_LICENSE := BSD
+
+# ----------------------------------------------------------------------------
+# Prepare
+# ----------------------------------------------------------------------------
+
+HOSTAPD_PATH := PATH=$(CROSS_PATH)
+#HOSTAPD_CONF_TOOL := NO
+HOSTAPD_MAKE_ENV := \
+ $(CROSS_ENV) \
+ LIBDIR=/lib \
+ BINDIR=/sbin
+
+
+$(STATEDIR)/hostapd.prepare:
+ @$(call targetinfo)
+# # run 'make clean' as hostapd's build system does not recognize config changes
+ @-cd $(HOSTAPD_DIR)/$(HOSTAPD_SUBDIR) && \
+ $(HOSTAPD_MAKE_ENV) $(HOSTAPD_PATH) $(MAKE) clean
+
+ @echo "CC=$(CROSS_CC)" > $(HOSTAPD_CONFIG) && \
+ echo "CFLAGS += -I$(PTXDIST_SYSROOT_TARGET)/include" >> $(HOSTAPD_CONFIG) && \
+ echo "CFLAGS += -I$(PTXDIST_SYSROOT_TARGET)/usr/include" >> $(HOSTAPD_CONFIG) && \
+ echo "LDFLAGS += -L$(PTXDIST_SYSROOT_TARGET)/lib" >> $(HOSTAPD_CONFIG) && \
+ echo "LDFLAGS += -L$(PTXDIST_SYSROOT_TARGET)/usr/lib" >> $(HOSTAPD_CONFIG)
+
+ @grep -e PTXCONF_HOSTAPD_ $(PTXDIST_PTXCONFIG) | \
+ sed -e 's/PTXCONF_HOSTAPD_/CONFIG_/g' -e 's/\"//g' >> $(HOSTAPD_CONFIG)
+
+ @$(call touch)
+
+# ----------------------------------------------------------------------------
+# Target-Install
+# ----------------------------------------------------------------------------
+
+$(STATEDIR)/hostapd.targetinstall:
+ @$(call targetinfo)
+
+ @$(call install_init, hostapd)
+ @$(call install_fixup, hostapd,PRIORITY,optional)
+ @$(call install_fixup, hostapd,SECTION,base)
+ @$(call install_fixup, hostapd,AUTHOR,"Matthias Fend <matthias.fend@wolfvision.com>")
+ @$(call install_fixup, hostapd,DESCRIPTION,missing)
+
+ @$(call install_copy, hostapd, 0, 0, 0755, $(HOSTAPD_DIR)/$(HOSTAPD_SUBDIR)/hostapd, /usr/bin/hostapd)
+
+ @$(call install_finish, hostapd)
+
+ @$(call touch)
+
+# ----------------------------------------------------------------------------
+# Clean
+# ----------------------------------------------------------------------------
+
+$(STATEDIR)/hostapd.clean:
+ @$(call targetinfo)
+ @-cd $(HOSTAPD_DIR) && \
+ $(HOSTAPD_ENV) $(HOSTAPD_PATH) $(MAKE) clean
+ @$(call clean_pkg, HOSTAPD)
+
+# vim: syntax=make
--
1.7.0.4
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:33 ` Pascal K
2013-05-07 8:39 ` Juergen Beisert
@ 2013-05-07 8:51 ` Josef Holzmayr
1 sibling, 0 replies; 11+ messages in thread
From: Josef Holzmayr @ 2013-05-07 8:51 UTC (permalink / raw)
To: ptxdist
Howdy!
... and while you're at keeping things on the mailing list, also do not
top-post please.
Am 07.05.2013 10:33, schrieb Pascal K:
> I'm looking into it. There is no "configure.ac <http://configure.ac>" so
> i suggest there is only a plain make file.
Better do not suggest, but unpack and have a look.
> But I don't know which further steps to get the package to compile.
Usually the README or INSTALL file in the package give a very good
impression of how to compile and install a package. I think you should
do the whole thing first natively on your desktoip box so you know how
its done, and _THEN_ proceed to packing these steps that you learned
into a ptxdist package.
Greetz
_____________________________________________________________
Josef Holzmayr
Dipl-Ing. (FH)
Entwicklung Embedded Devices / Software
Tel.: +49 8444 9204-48>
Fax: +49 8444 9204-50
holzmayr@rsi-elektrotechnik.de
R-S-I Elektrotechnik GmbH & Co. KG
Woelkestrasse 11
D-85301 Schweitenkirchen
www.rsi-elektrotechnik.de
_____________________________________________________________
Amtsgericht Ingolstadt - GmbH: HRB 191328 - KG: HRA 170363
Geschäftsführer: Dr.-Ing. Michael Sorg, Dipl.-Ing. Franz Sorg
USt-IdNr.: DE 128592548
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:33 ` Pascal K
@ 2013-05-07 8:39 ` Juergen Beisert
2013-05-07 8:51 ` Josef Holzmayr
1 sibling, 0 replies; 11+ messages in thread
From: Juergen Beisert @ 2013-05-07 8:39 UTC (permalink / raw)
To: ptxdist
Pascal K wrote:
> I'm looking into it. There is no "configure.ac" so i suggest there is only
> a plain make file.
>
> But I don't know which further steps to get the package to compile.
Please keep the mailing list at least on CC.
Regards,
Juergen
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | http://www.pengutronix.de/ |
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:17 Pascal K
2013-05-07 8:28 ` Juergen Beisert
@ 2013-05-07 8:34 ` Josef Holzmayr
2013-05-07 8:57 ` Matthias Fend
2 siblings, 0 replies; 11+ messages in thread
From: Josef Holzmayr @ 2013-05-07 8:34 UTC (permalink / raw)
To: ptxdist
Howdy!
Am 07.05.2013 10:17, schrieb Pascal K:
> My task:
> -> Building hostapd-2.0.tar.gz for my ARM Cortex A8 target board
->
> /$ ptxdist newpackage target /
> edited the mandatory fields, added md5sum, selected the package in
I don't know the hostapd package, but I'd guess that this is the basic
fault. You have to look at the package and find out which
configuration/build mechanism it uses (e.g. autotools, cmake, whatever)
and then start with the fitting newpackage target. That will take care
of the most obstacles, usually.
Greetz
_____________________________________________________________
Josef Holzmayr
Dipl-Ing. (FH)
Entwicklung Embedded Devices / Software
Tel.: +49 8444 9204-48>
Fax: +49 8444 9204-50
holzmayr@rsi-elektrotechnik.de
R-S-I Elektrotechnik GmbH & Co. KG
Woelkestrasse 11
D-85301 Schweitenkirchen
www.rsi-elektrotechnik.de
_____________________________________________________________
Amtsgericht Ingolstadt - GmbH: HRB 191328 - KG: HRA 170363
Geschäftsführer: Dr.-Ing. Michael Sorg, Dipl.-Ing. Franz Sorg
USt-IdNr.: DE 128592548
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:28 ` Juergen Beisert
@ 2013-05-07 8:33 ` Pascal K
2013-05-07 8:39 ` Juergen Beisert
2013-05-07 8:51 ` Josef Holzmayr
0 siblings, 2 replies; 11+ messages in thread
From: Pascal K @ 2013-05-07 8:33 UTC (permalink / raw)
To: Juergen Beisert
[-- Attachment #1.1: Type: text/plain, Size: 1967 bytes --]
I'm looking into it. There is no "configure.ac" so i suggest there is only
a plain make file.
But I don't know which further steps to get the package to compile.
Best regards,
Pascal
2013/5/7 Juergen Beisert <jbe@pengutronix.de>
> Hi Pascal,
>
> Pascal K wrote:
> > I'am beginning to use PTXdist, so I followed the How to become a PTXdist
> > Guru Manual to get started.
> > But there is some information which I don't find/don't get.
> >
> > My task:
> > -> Building hostapd-2.0.tar.gz for my ARM Cortex A8 target board
> >
> > So I tried to follow section 4.2.2 in the manual.
> >
> > *$ ptxdist newpackage target *
> > edited the mandatory fields, added md5sum, selected the package in
> > *$ ptxdist menuconfig
> > $ ptxdist get hostapd
> > $ ptxdist extract hostapd
> > $ ptxdist prepare hostapd*
> > and finally tried edited inside the hostapd folder the defconfig file to
> > .config
> > *$ ptxdist compile hostapd *
> >
> > now gives me the error that
> >
> > *make[1]: Entering directory
> >
> `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> > make[1]: *** No targets specified and no makefile found. Stop.
> > make[1]: Leaving directory
> >
> `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> make: ***
> >
> [/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/state/hostapd.compile]
> Error 2*
> >
> >
> > So I think I missed a step or a went with the wrong option at the
> > beginning.
> > Could someone give me an advice, that would be great!
>
> What kind of buildsystem this package uses? Autotools? Simple Makefile? The
> rule file is a translator between PTXdist and the package's buildsystem.
>
> Regards,
> Jürgen
>
> --
> Pengutronix e.K. | Juergen Beisert
> |
> Linux Solutions for Science and Industry | http://www.pengutronix.de/ |
>
[-- Attachment #1.2: Type: text/html, Size: 2869 bytes --]
[-- Attachment #2: Type: text/plain, Size: 48 bytes --]
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [ptxdist] Building hostapd for PTXdist and an ARM Target
2013-05-07 8:17 Pascal K
@ 2013-05-07 8:28 ` Juergen Beisert
2013-05-07 8:33 ` Pascal K
2013-05-07 8:34 ` Josef Holzmayr
2013-05-07 8:57 ` Matthias Fend
2 siblings, 1 reply; 11+ messages in thread
From: Juergen Beisert @ 2013-05-07 8:28 UTC (permalink / raw)
To: ptxdist; +Cc: Pascal K
Hi Pascal,
Pascal K wrote:
> I'am beginning to use PTXdist, so I followed the How to become a PTXdist
> Guru Manual to get started.
> But there is some information which I don't find/don't get.
>
> My task:
> -> Building hostapd-2.0.tar.gz for my ARM Cortex A8 target board
>
> So I tried to follow section 4.2.2 in the manual.
>
> *$ ptxdist newpackage target *
> edited the mandatory fields, added md5sum, selected the package in
> *$ ptxdist menuconfig
> $ ptxdist get hostapd
> $ ptxdist extract hostapd
> $ ptxdist prepare hostapd*
> and finally tried edited inside the hostapd folder the defconfig file to
> .config
> *$ ptxdist compile hostapd *
>
> now gives me the error that
>
> *make[1]: Entering directory
> `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
> make[1]: *** No targets specified and no makefile found. Stop.
> make[1]: Leaving directory
> `/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0' make: ***
> [/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/state/hostapd.compile] Error 2*
>
>
> So I think I missed a step or a went with the wrong option at the
> beginning.
> Could someone give me an advice, that would be great!
What kind of buildsystem this package uses? Autotools? Simple Makefile? The
rule file is a translator between PTXdist and the package's buildsystem.
Regards,
Jürgen
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | http://www.pengutronix.de/ |
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
* [ptxdist] Building hostapd for PTXdist and an ARM Target
@ 2013-05-07 8:17 Pascal K
2013-05-07 8:28 ` Juergen Beisert
` (2 more replies)
0 siblings, 3 replies; 11+ messages in thread
From: Pascal K @ 2013-05-07 8:17 UTC (permalink / raw)
To: ptxdist
[-- Attachment #1.1: Type: text/plain, Size: 1204 bytes --]
Hello all,
I'am beginning to use PTXdist, so I followed the How to become a PTXdist
Guru Manual to get started.
But there is some information which I don't find/don't get.
My task:
-> Building hostapd-2.0.tar.gz for my ARM Cortex A8 target board
So I tried to follow section 4.2.2 in the manual.
*$ ptxdist newpackage target *
edited the mandatory fields, added md5sum, selected the package in
*$ ptxdist menuconfig
$ ptxdist get hostapd
$ ptxdist extract hostapd
$ ptxdist prepare hostapd*
and finally tried edited inside the hostapd folder the defconfig file to
.config
*$ ptxdist compile hostapd *
now gives me the error that
*make[1]: Entering directory
`/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
make[1]: *** No targets specified and no makefile found. Stop.
make[1]: Leaving directory
`/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/build-target/hostapd-2.0'
make: ***
[/opt/PHYTEC_BSPs/phyCORE-AM335x-PD12.1.1/platform-phyCORE-AM335x/state/hostapd.compile]
Error 2*
So I think I missed a step or a went with the wrong option at the
beginning.
Could someone give me an advice, that would be great!
Best regards,
Pascal
[-- Attachment #1.2: Type: text/html, Size: 1391 bytes --]
[-- Attachment #2: Type: text/plain, Size: 48 bytes --]
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2013-07-01 7:14 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-05-07 11:24 [ptxdist] Building hostapd for PTXdist and an ARM Target Pascal K
-- strict thread matches above, loose matches on Subject: below --
2013-05-07 8:17 Pascal K
2013-05-07 8:28 ` Juergen Beisert
2013-05-07 8:33 ` Pascal K
2013-05-07 8:39 ` Juergen Beisert
2013-05-07 8:51 ` Josef Holzmayr
2013-05-07 8:34 ` Josef Holzmayr
2013-05-07 8:57 ` Matthias Fend
2013-06-28 16:08 ` irfan rafique
2013-07-01 6:45 ` Matthias Fend
2013-07-01 7:14 ` Pascal K
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox