mailarchive of the ptxdist mailing list
 help / color / mirror / Atom feed
From: Ladislav Michl <ladis@linux-mips.org>
To: ptxdist@pengutronix.de
Subject: [ptxdist] [PATCH] dnsmasq: optionally enable DBus support
Date: Tue, 10 Mar 2020 17:01:12 +0100	[thread overview]
Message-ID: <20200310160112.GA1293144@lenoch> (raw)

As projectroot's dnsmasq.conf is copied from example config and
needs to be modified to match BSP needs anyway, let's remove
config from projectroot altogether.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
---
 projectroot/etc/dnsmasq.conf | 679 -----------------------------------
 rules/dnsmasq.in             |  10 +-
 rules/dnsmasq.make           |  15 +
 3 files changed, 20 insertions(+), 684 deletions(-)
 delete mode 100644 projectroot/etc/dnsmasq.conf

diff --git a/projectroot/etc/dnsmasq.conf b/projectroot/etc/dnsmasq.conf
deleted file mode 100644
index 8548b43ed..000000000
--- a/projectroot/etc/dnsmasq.conf
+++ /dev/null
@@ -1,679 +0,0 @@
-# Configuration file for dnsmasq.
-#
-# Format is one option per line, legal options are the same
-# as the long options legal on the command line. See
-# "/usr/sbin/dnsmasq --help" or "man 8 dnsmasq" for details.
-
-# Listen on this specific port instead of the standard DNS port
-# (53). Setting this to zero completely disables DNS function,
-# leaving only DHCP and/or TFTP.
-#port=5353
-
-# The following two options make you a better netizen, since they
-# tell dnsmasq to filter out queries which the public DNS cannot
-# answer, and which load the servers (especially the root servers)
-# unnecessarily. If you have a dial-on-demand link they also stop
-# these requests from bringing up the link unnecessarily.
-
-# Never forward plain names (without a dot or domain part)
-#domain-needed
-# Never forward addresses in the non-routed address spaces.
-#bogus-priv
-
-# Uncomment these to enable DNSSEC validation and caching:
-# (Requires dnsmasq to be built with DNSSEC option.)
-#conf-file=%%PREFIX%%/share/dnsmasq/trust-anchors.conf
-#dnssec
-
-# Replies which are not DNSSEC signed may be legitimate, because the domain
-# is unsigned, or may be forgeries. Setting this option tells dnsmasq to
-# check that an unsigned reply is OK, by finding a secure proof that a DS
-# record somewhere between the root and the domain does not exist.
-# The cost of setting this is that even queries in unsigned domains will need
-# one or more extra DNS queries to verify.
-#dnssec-check-unsigned
-
-# Uncomment this to filter useless windows-originated DNS requests
-# which can trigger dial-on-demand links needlessly.
-# Note that (amongst other things) this blocks all SRV requests,
-# so don't use it if you use eg Kerberos, SIP, XMMP or Google-talk.
-# This option only affects forwarding, SRV records originating for
-# dnsmasq (via srv-host= lines) are not suppressed by it.
-#filterwin2k
-
-# Change this line if you want dns to get its upstream servers from
-# somewhere other that /etc/resolv.conf
-#resolv-file=
-
-# By  default,  dnsmasq  will  send queries to any of the upstream
-# servers it knows about and tries to favour servers to are  known
-# to  be  up.  Uncommenting this forces dnsmasq to try each query
-# with  each  server  strictly  in  the  order  they   appear   in
-# /etc/resolv.conf
-#strict-order
-
-# If you don't want dnsmasq to read /etc/resolv.conf or any other
-# file, getting its servers from this file instead (see below), then
-# uncomment this.
-#no-resolv
-
-# If you don't want dnsmasq to poll /etc/resolv.conf or other resolv
-# files for changes and re-read them then uncomment this.
-#no-poll
-
-# Add other name servers here, with domain specs if they are for
-# non-public domains.
-#server=/localnet/192.168.0.1
-
-# Example of routing PTR queries to nameservers: this will send all
-# address->name queries for 192.168.3/24 to nameserver 10.1.2.3
-#server=/3.168.192.in-addr.arpa/10.1.2.3
-
-# Add local-only domains here, queries in these domains are answered
-# from /etc/hosts or DHCP only.
-#local=/localnet/
-
-# Add domains which you want to force to an IP address here.
-# The example below send any host in double-click.net to a local
-# web-server.
-#address=/double-click.net/127.0.0.1
-
-# --address (and --server) work with IPv6 addresses too.
-#address=/www.thekelleys.org.uk/fe80::20d:60ff:fe36:f83
-
-# Add the IPs of all queries to yahoo.com, google.com, and their
-# subdomains to the vpn and search ipsets:
-#ipset=/yahoo.com/google.com/vpn,search
-
-# You can control how dnsmasq talks to a server: this forces
-# queries to 10.1.2.3 to be routed via eth1
-# server=10.1.2.3@eth1
-
-# and this sets the source (ie local) address used to talk to
-# 10.1.2.3 to 192.168.1.1 port 55 (there must be an interface with that
-# IP on the machine, obviously).
-# server=10.1.2.3@192.168.1.1#55
-
-# If you want dnsmasq to change uid and gid to something other
-# than the default, edit the following lines.
-#user=
-#group=
-
-# If you want dnsmasq to listen for DHCP and DNS requests only on
-# specified interfaces (and the loopback) give the name of the
-# interface (eg eth0) here.
-# Repeat the line for more than one interface.
-#interface=
-# Or you can specify which interface _not_ to listen on
-#except-interface=
-# Or which to listen on by address (remember to include 127.0.0.1 if
-# you use this.)
-#listen-address=
-# If you want dnsmasq to provide only DNS service on an interface,
-# configure it as shown above, and then use the following line to
-# disable DHCP and TFTP on it.
-#no-dhcp-interface=
-
-# On systems which support it, dnsmasq binds the wildcard address,
-# even when it is listening on only some interfaces. It then discards
-# requests that it shouldn't reply to. This has the advantage of
-# working even when interfaces come and go and change address. If you
-# want dnsmasq to really bind only the interfaces it is listening on,
-# uncomment this option. About the only time you may need this is when
-# running another nameserver on the same machine.
-#bind-interfaces
-
-# If you don't want dnsmasq to read /etc/hosts, uncomment the
-# following line.
-#no-hosts
-# or if you want it to read another file, as well as /etc/hosts, use
-# this.
-#addn-hosts=/etc/banner_add_hosts
-
-# Set this (and domain: see below) if you want to have a domain
-# automatically added to simple names in a hosts-file.
-#expand-hosts
-
-# Set the domain for dnsmasq. this is optional, but if it is set, it
-# does the following things.
-# 1) Allows DHCP hosts to have fully qualified domain names, as long
-#     as the domain part matches this setting.
-# 2) Sets the "domain" DHCP option thereby potentially setting the
-#    domain of all systems configured by DHCP
-# 3) Provides the domain part for "expand-hosts"
-#domain=thekelleys.org.uk
-
-# Set a different domain for a particular subnet
-#domain=wireless.thekelleys.org.uk,192.168.2.0/24
-
-# Same idea, but range rather then subnet
-#domain=reserved.thekelleys.org.uk,192.68.3.100,192.168.3.200
-
-# Uncomment this to enable the integrated DHCP server, you need
-# to supply the range of addresses available for lease and optionally
-# a lease time. If you have more than one network, you will need to
-# repeat this for each network on which you want to supply DHCP
-# service.
-#dhcp-range=192.168.0.50,192.168.0.150,12h
-
-# This is an example of a DHCP range where the netmask is given. This
-# is needed for networks we reach the dnsmasq DHCP server via a relay
-# agent. If you don't know what a DHCP relay agent is, you probably
-# don't need to worry about this.
-#dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h
-
-# This is an example of a DHCP range which sets a tag, so that
-# some DHCP options may be set only for this network.
-#dhcp-range=set:red,192.168.0.50,192.168.0.150
-
-# Use this DHCP range only when the tag "green" is set.
-#dhcp-range=tag:green,192.168.0.50,192.168.0.150,12h
-
-# Specify a subnet which can't be used for dynamic address allocation,
-# is available for hosts with matching --dhcp-host lines. Note that
-# dhcp-host declarations will be ignored unless there is a dhcp-range
-# of some type for the subnet in question.
-# In this case the netmask is implied (it comes from the network
-# configuration on the machine running dnsmasq) it is possible to give
-# an explicit netmask instead.
-#dhcp-range=192.168.0.0,static
-
-# Enable DHCPv6. Note that the prefix-length does not need to be specified
-# and defaults to 64 if missing/
-#dhcp-range=1234::2, 1234::500, 64, 12h
-
-# Do Router Advertisements, BUT NOT DHCP for this subnet.
-#dhcp-range=1234::, ra-only
-
-# Do Router Advertisements, BUT NOT DHCP for this subnet, also try and
-# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack
-# hosts. Use the DHCPv4 lease to derive the name, network segment and
-# MAC address and assume that the host will also have an
-# IPv6 address calculated using the SLAAC algorithm.
-#dhcp-range=1234::, ra-names
-
-# Do Router Advertisements, BUT NOT DHCP for this subnet.
-# Set the lifetime to 46 hours. (Note: minimum lifetime is 2 hours.)
-#dhcp-range=1234::, ra-only, 48h
-
-# Do DHCP and Router Advertisements for this subnet. Set the A bit in the RA
-# so that clients can use SLAAC addresses as well as DHCP ones.
-#dhcp-range=1234::2, 1234::500, slaac
-
-# Do Router Advertisements and stateless DHCP for this subnet. Clients will
-# not get addresses from DHCP, but they will get other configuration information.
-# They will use SLAAC for addresses.
-#dhcp-range=1234::, ra-stateless
-
-# Do stateless DHCP, SLAAC, and generate DNS names for SLAAC addresses
-# from DHCPv4 leases.
-#dhcp-range=1234::, ra-stateless, ra-names
-
-# Do router advertisements for all subnets where we're doing DHCPv6
-# Unless overridden by ra-stateless, ra-names, et al, the router
-# advertisements will have the M and O bits set, so that the clients
-# get addresses and configuration from DHCPv6, and the A bit reset, so the
-# clients don't use SLAAC addresses.
-#enable-ra
-
-# Supply parameters for specified hosts using DHCP. There are lots
-# of valid alternatives, so we will give examples of each. Note that
-# IP addresses DO NOT have to be in the range given above, they just
-# need to be on the same network. The order of the parameters in these
-# do not matter, it's permissible to give name, address and MAC in any
-# order.
-
-# Always allocate the host with Ethernet address 11:22:33:44:55:66
-# The IP address 192.168.0.60
-#dhcp-host=11:22:33:44:55:66,192.168.0.60
-
-# Always set the name of the host with hardware address
-# 11:22:33:44:55:66 to be "fred"
-#dhcp-host=11:22:33:44:55:66,fred
-
-# Always give the host with Ethernet address 11:22:33:44:55:66
-# the name fred and IP address 192.168.0.60 and lease time 45 minutes
-#dhcp-host=11:22:33:44:55:66,fred,192.168.0.60,45m
-
-# Give a host with Ethernet address 11:22:33:44:55:66 or
-# 12:34:56:78:90:12 the IP address 192.168.0.60. Dnsmasq will assume
-# that these two Ethernet interfaces will never be in use at the same
-# time, and give the IP address to the second, even if it is already
-# in use by the first. Useful for laptops with wired and wireless
-# addresses.
-#dhcp-host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.60
-
-# Give the machine which says its name is "bert" IP address
-# 192.168.0.70 and an infinite lease
-#dhcp-host=bert,192.168.0.70,infinite
-
-# Always give the host with client identifier 01:02:02:04
-# the IP address 192.168.0.60
-#dhcp-host=id:01:02:02:04,192.168.0.60
-
-# Always give the InfiniBand interface with hardware address
-# 80:00:00:48:fe:80:00:00:00:00:00:00:f4:52:14:03:00:28:05:81 the
-# ip address 192.168.0.61. The client id is derived from the prefix
-# ff:00:00:00:00:00:02:00:00:02:c9:00 and the last 8 pairs of
-# hex digits of the hardware address.
-#dhcp-host=id:ff:00:00:00:00:00:02:00:00:02:c9:00:f4:52:14:03:00:28:05:81,192.168.0.61
-
-# Always give the host with client identifier "marjorie"
-# the IP address 192.168.0.60
-#dhcp-host=id:marjorie,192.168.0.60
-
-# Enable the address given for "judge" in /etc/hosts
-# to be given to a machine presenting the name "judge" when
-# it asks for a DHCP lease.
-#dhcp-host=judge
-
-# Never offer DHCP service to a machine whose Ethernet
-# address is 11:22:33:44:55:66
-#dhcp-host=11:22:33:44:55:66,ignore
-
-# Ignore any client-id presented by the machine with Ethernet
-# address 11:22:33:44:55:66. This is useful to prevent a machine
-# being treated differently when running under different OS's or
-# between PXE boot and OS boot.
-#dhcp-host=11:22:33:44:55:66,id:*
-
-# Send extra options which are tagged as "red" to
-# the machine with Ethernet address 11:22:33:44:55:66
-#dhcp-host=11:22:33:44:55:66,set:red
-
-# Send extra options which are tagged as "red" to
-# any machine with Ethernet address starting 11:22:33:
-#dhcp-host=11:22:33:*:*:*,set:red
-
-# Give a fixed IPv6 address and name to client with
-# DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2
-# Note the MAC addresses CANNOT be used to identify DHCPv6 clients.
-# Note also that the [] around the IPv6 address are obligatory.
-#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5]
-
-# Ignore any clients which are not specified in dhcp-host lines
-# or /etc/ethers. Equivalent to ISC "deny unknown-clients".
-# This relies on the special "known" tag which is set when
-# a host is matched.
-#dhcp-ignore=tag:!known
-
-# Send extra options which are tagged as "red" to any machine whose
-# DHCP vendorclass string includes the substring "Linux"
-#dhcp-vendorclass=set:red,Linux
-
-# Send extra options which are tagged as "red" to any machine one
-# of whose DHCP userclass strings includes the substring "accounts"
-#dhcp-userclass=set:red,accounts
-
-# Send extra options which are tagged as "red" to any machine whose
-# MAC address matches the pattern.
-#dhcp-mac=set:red,00:60:8C:*:*:*
-
-# If this line is uncommented, dnsmasq will read /etc/ethers and act
-# on the ethernet-address/IP pairs found there just as if they had
-# been given as --dhcp-host options. Useful if you keep
-# MAC-address/host mappings there for other purposes.
-#read-ethers
-
-# Send options to hosts which ask for a DHCP lease.
-# See RFC 2132 for details of available options.
-# Common options can be given to dnsmasq by name:
-# run "dnsmasq --help dhcp" to get a list.
-# Note that all the common settings, such as netmask and
-# broadcast address, DNS server and default route, are given
-# sane defaults by dnsmasq. You very likely will not need
-# any dhcp-options. If you use Windows clients and Samba, there
-# are some options which are recommended, they are detailed at the
-# end of this section.
-
-# Override the default route supplied by dnsmasq, which assumes the
-# router is the same machine as the one running dnsmasq.
-#dhcp-option=3,1.2.3.4
-
-# Do the same thing, but using the option name
-#dhcp-option=option:router,1.2.3.4
-
-# Override the default route supplied by dnsmasq and send no default
-# route at all. Note that this only works for the options sent by
-# default (1, 3, 6, 12, 28) the same line will send a zero-length option
-# for all other option numbers.
-#dhcp-option=3
-
-# Set the NTP time server addresses to 192.168.0.4 and 10.10.0.5
-#dhcp-option=option:ntp-server,192.168.0.4,10.10.0.5
-
-# Send DHCPv6 option. Note [] around IPv6 addresses.
-#dhcp-option=option6:dns-server,[1234::77],[1234::88]
-
-# Send DHCPv6 option for namservers as the machine running
-# dnsmasq and another.
-#dhcp-option=option6:dns-server,[::],[1234::88]
-
-# Ask client to poll for option changes every six hours. (RFC4242)
-#dhcp-option=option6:information-refresh-time,6h
-
-# Set option 58 client renewal time (T1). Defaults to half of the
-# lease time if not specified. (RFC2132)
-#dhcp-option=option:T1,1m
-
-# Set option 59 rebinding time (T2). Defaults to 7/8 of the
-# lease time if not specified. (RFC2132)
-#dhcp-option=option:T2,2m
-
-# Set the NTP time server address to be the same machine as
-# is running dnsmasq
-#dhcp-option=42,0.0.0.0
-
-# Set the NIS domain name to "welly"
-#dhcp-option=40,welly
-
-# Set the default time-to-live to 50
-#dhcp-option=23,50
-
-# Set the "all subnets are local" flag
-#dhcp-option=27,1
-
-# Send the etherboot magic flag and then etherboot options (a string).
-#dhcp-option=128,e4:45:74:68:00:00
-#dhcp-option=129,NIC=eepro100
-
-# Specify an option which will only be sent to the "red" network
-# (see dhcp-range for the declaration of the "red" network)
-# Note that the tag: part must precede the option: part.
-#dhcp-option = tag:red, option:ntp-server, 192.168.1.1
-
-# The following DHCP options set up dnsmasq in the same way as is specified
-# for the ISC dhcpcd in
-# http://www.samba.org/samba/ftp/docs/textdocs/DHCP-Server-Configuration.txt
-# adapted for a typical dnsmasq installation where the host running
-# dnsmasq is also the host running samba.
-# you may want to uncomment some or all of them if you use
-# Windows clients and Samba.
-#dhcp-option=19,0           # option ip-forwarding off
-#dhcp-option=44,0.0.0.0     # set netbios-over-TCP/IP nameserver(s) aka WINS server(s)
-#dhcp-option=45,0.0.0.0     # netbios datagram distribution server
-#dhcp-option=46,8           # netbios node type
-
-# Send an empty WPAD option. This may be REQUIRED to get windows 7 to behave.
-#dhcp-option=252,"\n"
-
-# Send RFC-3397 DNS domain search DHCP option. WARNING: Your DHCP client
-# probably doesn't support this......
-#dhcp-option=option:domain-search,eng.apple.com,marketing.apple.com
-
-# Send RFC-3442 classless static routes (note the netmask encoding)
-#dhcp-option=121,192.168.1.0/24,1.2.3.4,10.0.0.0/8,5.6.7.8
-
-# Send vendor-class specific options encapsulated in DHCP option 43.
-# The meaning of the options is defined by the vendor-class so
-# options are sent only when the client supplied vendor class
-# matches the class given here. (A substring match is OK, so "MSFT"
-# matches "MSFT" and "MSFT 5.0"). This example sets the
-# mtftp address to 0.0.0.0 for PXEClients.
-#dhcp-option=vendor:PXEClient,1,0.0.0.0
-
-# Send microsoft-specific option to tell windows to release the DHCP lease
-# when it shuts down. Note the "i" flag, to tell dnsmasq to send the
-# value as a four-byte integer - that's what microsoft wants. See
-# http://technet2.microsoft.com/WindowsServer/en/library/a70f1bb7-d2d4-49f0-96d6-4b7414ecfaae1033.mspx?mfr=true
-#dhcp-option=vendor:MSFT,2,1i
-
-# Send the Encapsulated-vendor-class ID needed by some configurations of
-# Etherboot to allow is to recognise the DHCP server.
-#dhcp-option=vendor:Etherboot,60,"Etherboot"
-
-# Send options to PXELinux. Note that we need to send the options even
-# though they don't appear in the parameter request list, so we need
-# to use dhcp-option-force here.
-# See http://syslinux.zytor.com/pxe.php#special for details.
-# Magic number - needed before anything else is recognised
-#dhcp-option-force=208,f1:00:74:7e
-# Configuration file name
-#dhcp-option-force=209,configs/common
-# Path prefix
-#dhcp-option-force=210,/tftpboot/pxelinux/files/
-# Reboot time. (Note 'i' to send 32-bit value)
-#dhcp-option-force=211,30i
-
-# Set the boot filename for netboot/PXE. You will only need
-# this if you want to boot machines over the network and you will need
-# a TFTP server; either dnsmasq's built-in TFTP server or an
-# external one. (See below for how to enable the TFTP server.)
-#dhcp-boot=pxelinux.0
-
-# The same as above, but use custom tftp-server instead machine running dnsmasq
-#dhcp-boot=pxelinux,server.name,192.168.1.100
-
-# Boot for iPXE. The idea is to send two different
-# filenames, the first loads iPXE, and the second tells iPXE what to
-# load. The dhcp-match sets the ipxe tag for requests from iPXE.
-#dhcp-boot=undionly.kpxe
-#dhcp-match=set:ipxe,175 # iPXE sends a 175 option.
-#dhcp-boot=tag:ipxe,http://boot.ipxe.org/demo/boot.php
-
-# Encapsulated options for iPXE. All the options are
-# encapsulated within option 175
-#dhcp-option=encap:175, 1, 5b         # priority code
-#dhcp-option=encap:175, 176, 1b       # no-proxydhcp
-#dhcp-option=encap:175, 177, string   # bus-id
-#dhcp-option=encap:175, 189, 1b       # BIOS drive code
-#dhcp-option=encap:175, 190, user     # iSCSI username
-#dhcp-option=encap:175, 191, pass     # iSCSI password
-
-# Test for the architecture of a netboot client. PXE clients are
-# supposed to send their architecture as option 93. (See RFC 4578)
-#dhcp-match=peecees, option:client-arch, 0 #x86-32
-#dhcp-match=itanics, option:client-arch, 2 #IA64
-#dhcp-match=hammers, option:client-arch, 6 #x86-64
-#dhcp-match=mactels, option:client-arch, 7 #EFI x86-64
-
-# Do real PXE, rather than just booting a single file, this is an
-# alternative to dhcp-boot.
-#pxe-prompt="What system shall I netboot?"
-# or with timeout before first available action is taken:
-#pxe-prompt="Press F8 for menu.", 60
-
-# Available boot services. for PXE.
-#pxe-service=x86PC, "Boot from local disk"
-
-# Loads <tftp-root>/pxelinux.0 from dnsmasq TFTP server.
-#pxe-service=x86PC, "Install Linux", pxelinux
-
-# Loads <tftp-root>/pxelinux.0 from TFTP server at 1.2.3.4.
-# Beware this fails on old PXE ROMS.
-#pxe-service=x86PC, "Install Linux", pxelinux, 1.2.3.4
-
-# Use bootserver on network, found my multicast or broadcast.
-#pxe-service=x86PC, "Install windows from RIS server", 1
-
-# Use bootserver at a known IP address.
-#pxe-service=x86PC, "Install windows from RIS server", 1, 1.2.3.4
-
-# If you have multicast-FTP available,
-# information for that can be passed in a similar way using options 1
-# to 5. See page 19 of
-# http://download.intel.com/design/archives/wfm/downloads/pxespec.pdf
-
-
-# Enable dnsmasq's built-in TFTP server
-#enable-tftp
-
-# Set the root directory for files available via FTP.
-#tftp-root=/var/lib/misc/ftpd
-
-# Do not abort if the tftp-root is unavailable
-#tftp-no-fail
-
-# Make the TFTP server more secure: with this set, only files owned by
-# the user dnsmasq is running as will be send over the net.
-#tftp-secure
-
-# This option stops dnsmasq from negotiating a larger blocksize for TFTP
-# transfers. It will slow things down, but may rescue some broken TFTP
-# clients.
-#tftp-no-blocksize
-
-# Set the boot file name only when the "red" tag is set.
-#dhcp-boot=tag:red,pxelinux.red-net
-
-# An example of dhcp-boot with an external TFTP server: the name and IP
-# address of the server are given after the filename.
-# Can fail with old PXE ROMS. Overridden by --pxe-service.
-#dhcp-boot=/var/lib/misc/ftpd/pxelinux.0,boothost,192.168.0.3
-
-# If there are multiple external tftp servers having a same name
-# (using /etc/hosts) then that name can be specified as the
-# tftp_servername (the third option to dhcp-boot) and in that
-# case dnsmasq resolves this name and returns the resultant IP
-# addresses in round robin fashion. This facility can be used to
-# load balance the tftp load among a set of servers.
-#dhcp-boot=/var/lib/misc/ftpd/pxelinux.0,boothost,tftp_server_name
-
-# Set the limit on DHCP leases, the default is 150
-#dhcp-lease-max=150
-
-# The DHCP server needs somewhere on disk to keep its lease database.
-# This defaults to a sane location, but if you want to change it, use
-# the line below.
-#dhcp-leasefile=/var/lib/misc/dnsmasq.leases
-
-# Set the DHCP server to authoritative mode. In this mode it will barge in
-# and take over the lease for any client which broadcasts on the network,
-# whether it has a record of the lease or not. This avoids long timeouts
-# when a machine wakes up on a new network. DO NOT enable this if there's
-# the slightest chance that you might end up accidentally configuring a DHCP
-# server for your campus/company accidentally. The ISC server uses
-# the same option, and this URL provides more information:
-# http://www.isc.org/files/auth.html
-#dhcp-authoritative
-
-# Set the DHCP server to enable DHCPv4 Rapid Commit Option per RFC 4039.
-# In this mode it will respond to a DHCPDISCOVER message including a Rapid Commit
-# option with a DHCPACK including a Rapid Commit option and fully committed address
-# and configuration information. This must only be enabled if either the server is
-# the only server for the subnet, or multiple servers are present and they each
-# commit a binding for all clients.
-#dhcp-rapid-commit
-
-# Run an executable when a DHCP lease is created or destroyed.
-# The arguments sent to the script are "add" or "del",
-# then the MAC address, the IP address and finally the hostname
-# if there is one.
-#dhcp-script=/bin/echo
-
-# Set the cachesize here.
-#cache-size=150
-
-# If you want to disable negative caching, uncomment this.
-#no-negcache
-
-# Normally responses which come from /etc/hosts and the DHCP lease
-# file have Time-To-Live set as zero, which conventionally means
-# do not cache further. If you are happy to trade lower load on the
-# server for potentially stale date, you can set a time-to-live (in
-# seconds) here.
-#local-ttl=
-
-# If you want dnsmasq to detect attempts by Verisign to send queries
-# to unregistered .com and .net hosts to its sitefinder service and
-# have dnsmasq instead return the correct NXDOMAIN response, uncomment
-# this line. You can add similar lines to do the same for other
-# registries which have implemented wildcard A records.
-#bogus-nxdomain=64.94.110.11
-
-# If you want to fix up DNS results from upstream servers, use the
-# alias option. This only works for IPv4.
-# This alias makes a result of 1.2.3.4 appear as 5.6.7.8
-#alias=1.2.3.4,5.6.7.8
-# and this maps 1.2.3.x to 5.6.7.x
-#alias=1.2.3.0,5.6.7.0,255.255.255.0
-# and this maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40
-#alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0
-
-# Change these lines if you want dnsmasq to serve MX records.
-
-# Return an MX record named "maildomain.com" with target
-# servermachine.com and preference 50
-#mx-host=maildomain.com,servermachine.com,50
-
-# Set the default target for MX records created using the localmx option.
-#mx-target=servermachine.com
-
-# Return an MX record pointing to the mx-target for all local
-# machines.
-#localmx
-
-# Return an MX record pointing to itself for all local machines.
-#selfmx
-
-# Change the following lines if you want dnsmasq to serve SRV
-# records.  These are useful if you want to serve ldap requests for
-# Active Directory and other windows-originated DNS requests.
-# See RFC 2782.
-# You may add multiple srv-host lines.
-# The fields are <name>,<target>,<port>,<priority>,<weight>
-# If the domain part if missing from the name (so that is just has the
-# service and protocol sections) then the domain given by the domain=
-# config option is used. (Note that expand-hosts does not need to be
-# set for this to work.)
-
-# A SRV record sending LDAP for the example.com domain to
-# ldapserver.example.com port 389
-#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389
-
-# A SRV record sending LDAP for the example.com domain to
-# ldapserver.example.com port 389 (using domain=)
-#domain=example.com
-#srv-host=_ldap._tcp,ldapserver.example.com,389
-
-# Two SRV records for LDAP, each with different priorities
-#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,1
-#srv-host=_ldap._tcp.example.com,ldapserver.example.com,389,2
-
-# A SRV record indicating that there is no LDAP server for the domain
-# example.com
-#srv-host=_ldap._tcp.example.com
-
-# The following line shows how to make dnsmasq serve an arbitrary PTR
-# record. This is useful for DNS-SD. (Note that the
-# domain-name expansion done for SRV records _does_not
-# occur for PTR records.)
-#ptr-record=_http._tcp.dns-sd-services,"New Employee Page._http._tcp.dns-sd-services"
-
-# Change the following lines to enable dnsmasq to serve TXT records.
-# These are used for things like SPF and zeroconf. (Note that the
-# domain-name expansion done for SRV records _does_not
-# occur for TXT records.)
-
-#Example SPF.
-#txt-record=example.com,"v=spf1 a -all"
-
-#Example zeroconf
-#txt-record=_http._tcp.example.com,name=value,paper=A4
-
-# Provide an alias for a "local" DNS name. Note that this _only_ works
-# for targets which are names from DHCP or /etc/hosts. Give host
-# "bert" another name, bertrand
-#cname=bertand,bert
-
-# For debugging purposes, log each DNS query as it passes through
-# dnsmasq.
-#log-queries
-
-# Log lots of extra information about DHCP transactions.
-#log-dhcp
-
-# Include another lot of configuration options.
-#conf-file=/etc/dnsmasq.more.conf
-#conf-dir=/etc/dnsmasq.d
-
-# Include all the files in a directory except those ending in .bak
-#conf-dir=/etc/dnsmasq.d,.bak
-
-# Include all files in a directory which end in .conf
-#conf-dir=/etc/dnsmasq.d/,*.conf
-
-# If a DHCP client claims that its name is "wpad", ignore that.
-# This fixes a security hole. see CERT Vulnerability VU#598349
-#dhcp-name-match=set:wpad-ignore,wpad
-#dhcp-ignore-names=tag:wpad-ignore
diff --git a/rules/dnsmasq.in b/rules/dnsmasq.in
index aec63dd0f..0c7df9c23 100644
--- a/rules/dnsmasq.in
+++ b/rules/dnsmasq.in
@@ -32,12 +32,12 @@ comment "build options   ---"
 
 config DNSMASQ_DBUS
 	bool
-	prompt "include DBUS support [BROKEN]"
-	depends on BROKEN
+	prompt "include DBUS support"
 	help
-	  This enables DBUS support in dnsmasq. This is not only a build
-	  option. You also have to enable it at runtime. FIXME: Show how,
-	  see DBUS document in dnsmasq packet
+	  This enables DBUS support in dnsmasq. To enable it at runtime
+	  /etc/dnsmasq.conf needs to contain the line
+
+	  enable-dbus
 
 config DNSMASQ_TFTP
 	bool
diff --git a/rules/dnsmasq.make b/rules/dnsmasq.make
index bce8dd651..2972f68a3 100644
--- a/rules/dnsmasq.make
+++ b/rules/dnsmasq.make
@@ -38,6 +38,10 @@ DNSMASQ_MAKE_ENV := $(CROSS_ENV)
 
 DNSMASQ_COPT :=
 
+ifdef PTXCONF_DNSMASQ_DBUS
+DNSMASQ_COPT += -DHAVE_DBUS
+endif
+
 ifndef PTXCONF_DNSMASQ_TFTP
 DNSMASQ_COPT += -DNO_TFTP
 endif
@@ -68,6 +72,17 @@ $(STATEDIR)/dnsmasq.prepare:
 	@$(call targetinfo)
 	@$(call touch)
 
+# ----------------------------------------------------------------------------
+# Install
+# ----------------------------------------------------------------------------
+
+$(STATEDIR)/dnsmasq.install:
+	@$(call targetinfo)
+	@$(call world/install, DNSMASQ)
+	@install -vD -m 644 "$(DNSMASQ_DIR)/dnsmasq.conf.example" \
+		"$(DNSMASQ_PKGDIR)/etc/dnsmasq.conf"
+	@$(call touch)
+
 # ----------------------------------------------------------------------------
 # Target-Install
 # ----------------------------------------------------------------------------
-- 
2.25.1


_______________________________________________
ptxdist mailing list
ptxdist@pengutronix.de

             reply	other threads:[~2020-03-10 16:01 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-03-10 16:01 Ladislav Michl [this message]
2020-03-10 21:18 ` Alexander Dahl
2020-03-10 22:16   ` Ladislav Michl
2020-03-11  7:26     ` Alexander Dahl
2020-03-11 17:49       ` Ladislav Michl

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200310160112.GA1293144@lenoch \
    --to=ladis@linux-mips.org \
    --cc=ptxdist@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox