From: Michael Olbrich <m.olbrich@pengutronix.de>
To: ptxdist@pengutronix.de
Subject: Re: [ptxdist] [PATCH v2 3/3] iputils: add new package iputils
Date: Thu, 30 Jan 2014 09:48:13 +0100 [thread overview]
Message-ID: <20140130084813.GD9989@pengutronix.de> (raw)
In-Reply-To: <1390729284-6837-3-git-send-email-alex.aring@gmail.com>
On Sun, Jan 26, 2014 at 10:41:24AM +0100, Alexander Aring wrote:
> This patch adds another package for most common network binary tools
> like ping, ping6, etc.
>
> Signed-off-by: Alexander Aring <alex.aring@gmail.com>
> ---
> v2:
> - Add missing ALLYES
>
Thanks, all applied. I've cleaned up this patch a bit.
Michael
> rules/iputils.in | 118 ++++++++++++++++++++++++++++++++++++++++++++
> rules/iputils.make | 141 +++++++++++++++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 259 insertions(+)
> create mode 100644 rules/iputils.in
> create mode 100644 rules/iputils.make
>
> diff --git a/rules/iputils.in b/rules/iputils.in
> new file mode 100644
> index 0000000..a83fa5a
> --- /dev/null
> +++ b/rules/iputils.in
> @@ -0,0 +1,118 @@
> +## SECTION=networking
> +
> +menuconfig IPUTILS
> + tristate
> + prompt "iputils "
> + select LIBC_RESOLV if IPUTILS_PING6
> + select LIBCAP if IPUTILS_ARPING || IPUTILS_PING || IPUTILS_PING6 || IPUTILS_TRACEROUTE6
> + select GNUTLS if IPUTILS_PING6
> + select GNUTLS_OPENSSL if IPUTILS_PING6
> + help
> + The iputils package is set of small useful utilities for Linux
> + networking.
> +
> +if IPUTILS
> +
> +config IPUTILS_ARPING
> + bool
> + depends on !BUSYBOX_ARPING || ALLYES
> + prompt "arping"
> + help
> + Ping destination on device interface by ARP packets, using source
> + address source.
> +
> +comment "BusyBox' arping is selected!"
> + depends on BUSYBOX_ARPING
> +
> +config IPUTILS_CLOCKDIFF
> + bool
> + prompt "clockdiff"
> + help
> + Measures clock difference between us and destination with 1 msec
> + resolution.
> +
> +config IPUTILS_PING
> + bool
> + depends on !INETUTILS_PING || ALLYES
> + prompt "ping"
> + help
> + The ping command uses the ICMP protocol's mandatory ECHO_REQUEST datagram
> + to elicit an ICMP ECHO_RESPONSE from a host or gateway. ECHO_REQUEST
> + datagrams pings have an IP and ICMP header, followed by a struct
> + timeval and then an arbitrary number of pad bytes used to fill out
> + the packet.
> +
> +comment "BusyBox' ping is selected!"
> + depends on BUSYBOX_PING
> +
> +comment "inetutils' ping is selected!"
> + depends on INETUTILS_PING
> +
> +config IPUTILS_PING6
> + bool
> + depends on !INETUTILS_PING6 || ALLYES
> + prompt "ping6"
> + depends on GLOBAL_IPV6
> + help
> + The ping6 command is IPv6 version of ping, and can also send Node
> + Information Queries (RFC4620). Intermediate hops may not be allowed,
> + because IPv6 source routing was deprecated (RFC5095).
> +
> +comment "BusyBox' ping6 is selected!"
> + depends on BUSYBOX_PING6
> +
> +comment "inetutils' ping6 is selected!"
> + depends on INETUTILS_PING6
> +
> +config IPUTILS_RARPD
> + bool
> + prompt "rarpd"
> + help
> + Listens RARP (http://tools.ietf.org/rfc/rfc903.txt) requests from
> + clients. Provided MAC address of client is found in /etc/ethers
> + database and obtained host name is resolvable to an IP address
> + appropriate for attached network, rarpd answers to client with
> + RARPD reply carrying an IP address.
> +
> +config IPUTILS_RDISC
> + bool
> + prompt "rdisc"
> + help
> + The rdisc command implements client side of the ICMP router discover
> + protocol. rdisc is invoked at boot time to populate the network
> + routing tables with default routes.
> +
> +config IPUTILS_TFTPD
> + bool
> + depends on !INETUTILS_TFTPD || ALLYES
> + prompt "tftpd"
> + help
> +
> +comment "BusyBox' tftpd is selected!"
> + depends on BUSYBOX_TFTPD
> +
> +comment "inetutils' tftpd is selected!"
> + depends on INETUTILS_TFTPD
> +
> +config IPUTILS_TRACEPATH
> + bool
> + prompt "tracepath"
> + help
> +
> +config IPUTILS_TRACEPATH6
> + bool
> + prompt "tracepath6"
> + depends on GLOBAL_IPV6
> + help
> +
> +config IPUTILS_TRACEROUTE6
> + bool
> + depends on !BUSYBOX_TRACEROUTE6 || ALLYES
> + prompt "traceroute6"
> + depends on GLOBAL_IPV6
> + help
> +
> +comment "BusyBox' traceroute6 is selected!"
> + depends on BUSYBOX_TRACEROUTE6
> +
> +endif
> diff --git a/rules/iputils.make b/rules/iputils.make
> new file mode 100644
> index 0000000..9685370
> --- /dev/null
> +++ b/rules/iputils.make
> @@ -0,0 +1,141 @@
> +# -*-makefile-*-
> +#
> +# Copyright (C) 2014 by Alexander Aring <aar@pengutronix.de>
> +#
> +# See CREDITS for details about who has contributed to this project.
> +#
> +# For further information about the PTXdist project and license conditions
> +# see the README file.
> +#
> +
> +#
> +# We provide this package
> +#
> +PACKAGES-$(PTXCONF_IPUTILS) += iputils
> +
> +#
> +# Paths and names
> +#
> +IPUTILS_VERSION := s20121221
> +IPUTILS_MD5 := 6072aef64205720dd1893b375e184171
> +IPUTILS := iputils-$(IPUTILS_VERSION)
> +IPUTILS_SUFFIX := tar.bz2
> +IPUTILS_URL := http://www.skbuff.net/iputils/$(IPUTILS).$(IPUTILS_SUFFIX)
> +IPUTILS_SOURCE := $(SRCDIR)/$(IPUTILS).$(IPUTILS_SUFFIX)
> +IPUTILS_DIR := $(BUILDDIR)/$(IPUTILS)
> +IPUTILS_LICENSE := GPLv2
> +
> +# ----------------------------------------------------------------------------
> +# Prepare
> +# ----------------------------------------------------------------------------
> +
> +IPUTILS_CONF_TOOL := NO
> +IPUTILS_MAKEVARS := $(CROSS_ENV)
> +
> +# ----------------------------------------------------------------------------
> +# Install
> +# ----------------------------------------------------------------------------
> +
> +$(STATEDIR)/iputils.install:
> + @$(call targetinfo)
> + mkdir -p $(IPUTILS_PKGDIR)/usr/bin
> +
> +ifdef PTXCONF_IPUTILS_ARPING
> + install -m0755 $(IPUTILS_DIR)/arping $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_CLOCKDIFF
> + install -m0755 $(IPUTILS_DIR)/clockdiff $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_PING
> + install -m0755 $(IPUTILS_DIR)/ping $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_PING6
> + install -m0755 $(IPUTILS_DIR)/ping6 $(IPUTILS_PKGDIR)/usr/bin
> +endif
> + @$(call touch)
> +
> +ifdef PTXCONF_IPUTILS_RARPD
> + install -m0755 $(IPUTILS_DIR)/rarpd $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_RDISC
> + install -m0755 $(IPUTILS_DIR)/rdisc $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TFTPD
> + install -m0755 $(IPUTILS_DIR)/tftpd $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TRACEPATH
> + install -m0755 $(IPUTILS_DIR)/tracepath $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TRACEPATH6
> + install -m0755 $(IPUTILS_DIR)/tracepath6 $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TRACEROUTE6
> + install -m0755 $(IPUTILS_DIR)/traceroute6 $(IPUTILS_PKGDIR)/usr/bin
> +endif
> +
> +# ----------------------------------------------------------------------------
> +# Target-Install
> +# ----------------------------------------------------------------------------
> +
> +$(STATEDIR)/iputils.targetinstall:
> + @$(call targetinfo)
> +
> + @$(call install_init, iputils)
> + @$(call install_fixup, iputils,PRIORITY,optional)
> + @$(call install_fixup, iputils,SECTION,base)
> + @$(call install_fixup, iputils,AUTHOR,"Alexander Aring <aar@pengutronix.de>")
> + @$(call install_fixup, iputils,DESCRIPTION,missing)
> +
> +ifdef PTXCONF_IPUTILS_ARPING
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/arping)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_CLOCKDIFF
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/clockdiff)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_PING
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/ping)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_PING6
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/ping6)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_RARPD
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/rarpd)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_RDISC
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/rdisc)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TFTPD
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/tftpd)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TRACEPATH
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/tracepath)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TRACEPATH6
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/tracepath6)
> +endif
> +
> +ifdef PTXCONF_IPUTILS_TRACEROUTE6
> + @$(call install_copy, iputils, 0, 0, 0755, -, /usr/bin/traceroute6)
> +endif
> +
> + @$(call install_finish, iputils)
> +
> + @$(call touch)
> +
> +# vim: syntax=make
> --
> 1.8.5.3
>
>
> --
> ptxdist mailing list
> ptxdist@pengutronix.de
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
--
ptxdist mailing list
ptxdist@pengutronix.de
next prev parent reply other threads:[~2014-01-30 8:48 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-26 9:41 [ptxdist] [PATCH v2 1/3] inetutils: add missing depends on !BUSYBOX_TFTPD Alexander Aring
2014-01-26 9:41 ` [ptxdist] [PATCH v2 2/3] gnutls: add support for openssl compatibility Alexander Aring
2014-01-26 9:41 ` [ptxdist] [PATCH v2 3/3] iputils: add new package iputils Alexander Aring
2014-01-30 8:48 ` Michael Olbrich [this message]
2014-01-30 9:19 ` Alexander Aring
2014-01-26 10:23 [ptxdist] [PATCH v2 1/3] inetutils: add missing depends on !BUSYBOX_TFTPD Alexander Aring
2014-01-26 10:23 ` [ptxdist] [PATCH v2 3/3] iputils: add new package iputils Alexander Aring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140130084813.GD9989@pengutronix.de \
--to=m.olbrich@pengutronix.de \
--cc=ptxdist@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox