* [ptxdist] Mini2440 touchscreen VS two versions of hardware
@ 2013-09-16 15:17 Pawel Suchanecki
2013-09-17 14:28 ` Jürgen Beisert
0 siblings, 1 reply; 2+ messages in thread
From: Pawel Suchanecki @ 2013-09-16 15:17 UTC (permalink / raw)
To: ptxdist
[-- Attachment #1: Type: text/plain, Size: 1593 bytes --]
Hello,
I have two versions of FriendlyARM's Mini2440 hardware: with 1GB and
with 256MB of NAND and two A70 screens (each bought as a bundle).
The first runs just fine (1GB NAND), touch screen works without
problem. In the second (256GB NAND) it does not. But the touchscreen
is operational: it worked with the default Linux install (the one they
ship device with, kernel `uname -a`: Linux "FriendlyARM
2.6.32.2-FriendlyARM #1 Wed Jun 6 15:43:59 HKT 2012 armv4tl unknown").
Both devices run the same barebox, kernel and rootfs versions, built
using OSELAS.BSP-Pengutronix-Mini2440-2012.12.0, Linux 3.7.1, barebox
2013.05.1.
I have verified that (on the faulty machine):
* /sys/bus/platform/drivers/samsung-ts exists
* /sys/bus/platform/devices/s3c2440-ts exists
* I use "mini2440=1tb" kernel parameter
following "OSELAS Quickstart for FriendlyARM Mini2440" in section
"8.10.1 If the Touchscreen does not work".
However `evtest /dev/input/touchscreen` does not show any events on
faulty machine and works flawlessly on the good one.
Also the A70 screen from the 256MB NAND based set does not work with
the 1GB NAND board
*and*
A70 screen from 1GB NAND based set does not work with 256MB NAND board.
What can be the cause of this? How can I address this issue?
Will using a newer or older kernel help? Which version do you suggest
to start with?
Thank you,
Pawel
p.s. I attach dmesgs for both devices, they differ slightly, namely on line:
s3c-i2c s3c2440-i2c: registers c4848000 (c3873520, c03aa898) <-- 1GB
s3c-i2c s3c2440-i2c: registers c4848000 (c3863520, c03aa898) <-- 256MB
[-- Attachment #2: dmesg-256MB_NAND.txt --]
[-- Type: text/plain, Size: 10176 bytes --]
Booting Linux on physical CPU 0
Initializing cgroup subsys cpu
Linux version 3.7.1-ptx-2012.12.0 (pawel@devbox) (gcc version 4.7.2 (OSELAS.Toolchain-2012.12.1) ) #6 PREEMPT Thu Aug 8 23:11:13 CEST 2013
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: MINI2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c03c5d64, node_mem_map c03e5000
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttySAC0,115200 mini2440=1tb ip=none root=/dev/mtdblock3 rootfstype=jffs2 noinitrd mtdparts=nand:512k(barebox),384k(bareboxenv),2048k(kern
el),-(root)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60944k/60944k available, 4592k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc037fb3c (3551 kB)
.init : 0xc0380000 - 0xc039bf50 ( 112 kB)
.data : 0xc039c000 - 0xc03c64a0 ( 170 kB)
.bss : 0xc03c64c4 - 0xc03e4a38 ( 122 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:85
irq: clearing pending ext status 00000080
irq: clearing subpending status 00000003
timer tcon=00500000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57
sched_clock: 32 bits at 200 Hz, resolution 5000000ns, wraps every 4294967291ms
Calibrating delay loop... 201.52 BogoMIPS (lpj=503808)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x302ee398 - 0x302ee3d4
devtmpfs: initialized
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
i2c-core: driver [dummy] registered
MINI2440: Option string mini2440=1tb
MINI2440: LCD
0:240x320 [1:800x480]
2:1024x768 3:240x320
4:640x480 5:240x320
6:320x240 7:480x272
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C244X: Clock Support, DVS off
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at c4846000, irq 33
DMA channel 1 at c4846040, irq 34
DMA channel 2 at c4846080, irq 35
DMA channel 3 at c48460c0, irq 36
s3c24xx-pwm s3c24xx-pwm.0: tin at 25312500, tdiv at 25312500, tin=divclk, base 0
S3C24XX CPU Frequency driver, s3c244x cpu support
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c: clock source c03a8890
s3c-i2c s3c2440-i2c: registers c4848000 (c3863520, c03aa898)
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: pdata desired frequency 100000
s3c-i2c s3c2440-i2c: IICLC=00000006
s3c-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c-i2c s3c2440-i2c: S3C2410_IICCON=0xa0
i2c i2c-0: adapter [s3c2410-i2c] registered
i2c 0-0050: uevent
i2c i2c-0: client [24c08] registered with bus id 0-0050
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
s3c-adc s3c24xx-adc: attached adc driver
jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
msgmni has been set to 119
io scheduler noop registered
io scheduler cfq registered (default)
s3c2410-lcd s3c2410-lcd: fb0: s3c2410fb frame buffer device
s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
console [ttySAC0] enabled
s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
at24 0-0050: probe
i2c 0-0051: uevent
dummy 0-0051: probe
i2c i2c-0: client [dummy] registered with bus id 0-0051
i2c 0-0052: uevent
dummy 0-0052: probe
i2c i2c-0: client [dummy] registered with bus id 0-0052
i2c 0-0053: uevent
dummy 0-0053: probe
i2c i2c-0: client [dummy] registered with bus id 0-0053
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 16 bytes/write
i2c-core: driver [at24] registered
s3c24xx-nand s3c2440-nand: Tacls=1, 9ns Twrph0=3 29ns, Twrph1=2 19ns
s3c24xx-nand s3c2440-nand: NAND hardware ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit), page size: 2048, OOB size: 64
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x0000049c0000
nand_read_bbt: bad block at 0x000005ae0000
nand_read_bbt: bad block at 0x00000dfa0000
4 cmdlinepart partitions found on MTD device nand
Creating 4 MTD partitions on "nand":
0x000000000000-0x000000080000 : "barebox"
0x000000080000-0x0000000e0000 : "bareboxenv"
0x0000000e0000-0x0000002e0000 : "kernel"
0x0000002e0000-0x000010000000 : "root"
s3c24xx-nand s3c2440-nand: clock idle support enabled
dm9000 Ethernet Driver, V1.31
eth0: dm9000e at c4978300,c497a304 IRQ 51 MAC: 00:00:00:fa:00:02 (chip)
usbcore: registered new interface driver rt2800usb
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
samsung-ts s3c2440-ts: driver attached, registering input device
input: S3C24XX TouchScreen as /devices/virtual/input/input0
input: pwm-beeper as /devices/platform/s3c24xx-pwm.0/pwm-beeper/input/input1
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c-core: driver [smbus_alert] registered
i2c /dev entries driver
i2c-dev: adapter [s3c2410-i2c] registered as minor 0
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq disabled
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: HCIATH3K protocol initialized
Bluetooth: HCI Three-wire UART (H5) protocol initialized
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
cpuidle: using governor ladder
s3c-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
s3c-sdi s3c2440-sdi: running at 398kHz (requested: 400kHz).
s3c-sdi s3c2440-sdi: powered down.
s3c-sdi s3c2440-sdi: mmc0 - using pio, hw SDIO IRQ
Registered led device: led1
Registered led device: led2
Registered led device: led3
Registered led device: led4
Registered led device: backlight
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
input: gpio-keys as /devices/platform/gpio-keys/input/input2
s3c-rtc s3c2410-rtc: setting system clock to 2055-02-03 04:41:18 UTC (2685242478)
usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.2: new full-speed USB device number 3 using s3c2410-ohci
scsi0 : usb-storage 1-1.2:1.0
scsi 0:0:0:0: Direct-Access Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 3903488 512-byte logical blocks: (1.99 GB/1.86 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
sd 0:0:0:0: [sda] No Caching mode page present
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] No Caching mode page present
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 0:0:0:0: [sda] No Caching mode page present
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
VFS: Mounted root (jffs2 filesystem) on device 31:3.
devtmpfs: mounted
Freeing init memory: 108K
>udevd[416]: starting version 182
at24 0-0050: uevent
dummy 0-0051: uevent
dummy 0-0052: uevent
dummy 0-0053: uevent
at24 0-0050: uevent
at24 0-0050: uevent
at24 0-0050: uevent
dummy 0-0051: uevent
dummy 0-0051: uevent
dummy 0-0051: uevent
dummy 0-0052: uevent
dummy 0-0053: uevent
dummy 0-0053: uevent
dummy 0-0052: uevent
dummy 0-0052: uevent
dummy 0-0053: uevent
[-- Attachment #3: dmesg-1GB_NAND.txt --]
[-- Type: text/plain, Size: 9285 bytes --]
Booting Linux on physical CPU 0
Initializing cgroup subsys cpu
Linux version 3.7.1-ptx-2012.12.0 (pawel@devbox) (gcc version 4.7.2 (OSELAS.Toolchain-2012.12.1) ) #6 PREEMPT Thu Aug 8 23:11:13 CEST 2013
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: MINI2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c03c5d64, node_mem_map c03e5000
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttySAC0,115200 mini2440=1tb ip=none root=/dev/mtdblock3 rootfstype=jffs2 noinitrd mtdparts=nand:512k(barebox),384k(bareboxenv),2048k(kernel),-(root)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60944k/60944k available, 4592k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc037fb3c (3551 kB)
.init : 0xc0380000 - 0xc039bf50 ( 112 kB)
.data : 0xc039c000 - 0xc03c64a0 ( 170 kB)
.bss : 0xc03c64c4 - 0xc03e4a38 ( 122 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:85
irq: clearing pending ext status 00000080
irq: clearing subpending status 00000002
timer tcon=00500000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57
sched_clock: 32 bits at 200 Hz, resolution 5000000ns, wraps every 4294967291ms
Calibrating delay loop... 201.52 BogoMIPS (lpj=503808)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x302ee398 - 0x302ee3d4
devtmpfs: initialized
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
i2c-core: driver [dummy] registered
MINI2440: Option string mini2440=1tb
MINI2440: LCD
0:240x320 [1:800x480]
2:1024x768 3:240x320
4:640x480 5:240x320
6:320x240 7:480x272
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C244X: Clock Support, DVS off
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at c4846000, irq 33
DMA channel 1 at c4846040, irq 34
DMA channel 2 at c4846080, irq 35
DMA channel 3 at c48460c0, irq 36
s3c24xx-pwm s3c24xx-pwm.0: tin at 25312500, tdiv at 25312500, tin=divclk, base 0
S3C24XX CPU Frequency driver, s3c244x cpu support
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c: clock source c03a8890
s3c-i2c s3c2440-i2c: registers c4848000 (c3873520, c03aa898)
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: pdata desired frequency 100000
s3c-i2c s3c2440-i2c: IICLC=00000006
s3c-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c-i2c s3c2440-i2c: S3C2410_IICCON=0xa0
i2c i2c-0: adapter [s3c2410-i2c] registered
i2c 0-0050: uevent
i2c i2c-0: client [24c08] registered with bus id 0-0050
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
s3c-adc s3c24xx-adc: attached adc driver
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 119
io scheduler noop registered
io scheduler cfq registered (default)
s3c2410-lcd s3c2410-lcd: fb0: s3c2410fb frame buffer device
s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
console [ttySAC0] enabled
s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
at24 0-0050: probe
i2c 0-0051: uevent
dummy 0-0051: probe
i2c i2c-0: client [dummy] registered with bus id 0-0051
i2c 0-0052: uevent
dummy 0-0052: probe
i2c i2c-0: client [dummy] registered with bus id 0-0052
i2c 0-0053: uevent
dummy 0-0053: probe
i2c i2c-0: client [dummy] registered with bus id 0-0053
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 16 bytes/write
i2c-core: driver [at24] registered
s3c24xx-nand s3c2440-nand: Tacls=1, 9ns Twrph0=3 29ns, Twrph1=2 19ns
s3c24xx-nand s3c2440-nand: NAND hardware ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit), page size: 2048, OOB size: 64
Bad block table found at page 524224, version 0x01
Bad block table found at page 524160, version 0x01
4 cmdlinepart partitions found on MTD device nand
Creating 4 MTD partitions on "nand":
0x000000000000-0x000000080000 : "barebox"
0x000000080000-0x0000000e0000 : "bareboxenv"
0x0000000e0000-0x0000002e0000 : "kernel"
0x0000002e0000-0x000040000000 : "root"
s3c24xx-nand s3c2440-nand: clock idle support enabled
dm9000 Ethernet Driver, V1.31
eth0: dm9000e at c4978300,c497a304 IRQ 51 MAC: 00:00:00:fa:00:02 (chip)
usbcore: registered new interface driver rt2800usb
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
samsung-ts s3c2440-ts: driver attached, registering input device
input: S3C24XX TouchScreen as /devices/virtual/input/input0
input: pwm-beeper as /devices/platform/s3c24xx-pwm.0/pwm-beeper/input/input1
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c-core: driver [smbus_alert] registered
i2c /dev entries driver
i2c-dev: adapter [s3c2410-i2c] registered as minor 0
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq disabled
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
Bluetooth: HCILL protocol initialized
Bluetooth: HCIATH3K protocol initialized
Bluetooth: HCI Three-wire UART (H5) protocol initialized
usbcore: registered new interface driver btusb
Bluetooth: Generic Bluetooth SDIO driver ver 0.1
cpuidle: using governor ladder
s3c-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz).
s3c-sdi s3c2440-sdi: running at 398kHz (requested: 400kHz).
s3c-sdi s3c2440-sdi: powered down.
s3c-sdi s3c2440-sdi: mmc0 - using pio, hw SDIO IRQ
Registered led device: led1
Registered led device: led2
Registered led device: led3
Registered led device: led4
Registered led device: backlight
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
lib80211: common routines for IEEE802.11 drivers
lib80211_crypt: registered algorithm 'NULL'
input: gpio-keys as /devices/platform/gpio-keys/input/input2
s3c-rtc s3c2410-rtc: setting system clock to 2013-09-15 23:05:42 UTC (1379286342)
jffs2: Empty flash at 0x05cd8f2c ends at 0x05cd9000
VFS: Mounted root (jffs2 filesystem) on device 31:3.
devtmpfs: mounted
Freeing init memory: 108K
>udevd[400]: starting version 182
at24 0-0050: uevent
dummy 0-0051: uevent
dummy 0-0052: uevent
dummy 0-0053: uevent
at24 0-0050: uevent
at24 0-0050: uevent
dummy 0-0051: uevent
dummy 0-0051: uevent
dummy 0-0051: uevent
dummy 0-0052: uevent
dummy 0-0052: uevent
dummy 0-0053: uevent
dummy 0-0053: uevent
at24 0-0050: uevent
dummy 0-0052: uevent
dummy 0-0053: uevent
[-- Attachment #4: Type: text/plain, Size: 48 bytes --]
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [ptxdist] Mini2440 touchscreen VS two versions of hardware
2013-09-16 15:17 [ptxdist] Mini2440 touchscreen VS two versions of hardware Pawel Suchanecki
@ 2013-09-17 14:28 ` Jürgen Beisert
0 siblings, 0 replies; 2+ messages in thread
From: Jürgen Beisert @ 2013-09-17 14:28 UTC (permalink / raw)
To: ptxdist; +Cc: Pawel Suchanecki
Hi Pawel,
On Monday 16 September 2013 17:17:31 Pawel Suchanecki wrote:
> I have two versions of FriendlyARM's Mini2440 hardware: with 1GB and
> with 256MB of NAND and two A70 screens (each bought as a bundle).
> [...]
This question is not related to PTXdist. Please use the
oselas@community.pengutronix.de mailing list instead.
Regards,
Juergen
--
Pengutronix e.K. | Juergen Beisert |
Linux Solutions for Science and Industry | http://www.pengutronix.de/ |
--
ptxdist mailing list
ptxdist@pengutronix.de
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2013-09-17 14:28 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2013-09-16 15:17 [ptxdist] Mini2440 touchscreen VS two versions of hardware Pawel Suchanecki
2013-09-17 14:28 ` Jürgen Beisert
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox