From mboxrd@z Thu Jan  1 00:00:00 1970
Return-path: <ptxdist-bounces@pengutronix.de>
Received: from dude.hi.pengutronix.de ([2001:6f8:1178:2:21e:67ff:fe11:9c5c])
	by metis.ext.pengutronix.de with esmtp (Exim 4.72)
	(envelope-from <rsc@pengutronix.de>) id 1TK1YZ-00047T-Kd
	for ptxdist@pengutronix.de; Fri, 05 Oct 2012 08:38:43 +0200
Received: from rsc by dude.hi.pengutronix.de with local (Exim 4.80)
	(envelope-from <rsc@pengutronix.de>) id 1TK1YZ-0000BP-Jq
	for ptxdist@pengutronix.de; Fri, 05 Oct 2012 08:38:43 +0200
Date: Fri, 5 Oct 2012 08:38:43 +0200
From: Robert Schwebel <r.schwebel@pengutronix.de>
Message-ID: <20121005063843.GD23204@pengutronix.de>
References: <loom.20121004T154200-420@post.gmane.org>
MIME-Version: 1.0
Content-Disposition: inline
In-Reply-To: <loom.20121004T154200-420@post.gmane.org>
Subject: Re: [ptxdist] link detection
Reply-To: ptxdist@pengutronix.de
List-Id: PTXdist Development Mailing List <ptxdist.pengutronix.de>
List-Unsubscribe: <http://metis.pengutronix.de/cgi-bin/mailman/options/ptxdist>, 
	<mailto:ptxdist-request@pengutronix.de?subject=unsubscribe>
List-Archive: <http://metis.pengutronix.de/pipermail/ptxdist>
List-Post: <mailto:ptxdist@pengutronix.de>
List-Help: <mailto:ptxdist-request@pengutronix.de?subject=help>
List-Subscribe: <http://metis.pengutronix.de/cgi-bin/mailman/listinfo/ptxdist>, 
	<mailto:ptxdist-request@pengutronix.de?subject=subscribe>
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
Sender: ptxdist-bounces@pengutronix.de
Errors-To: ptxdist-bounces@pengutronix.de
To: ptxdist@pengutronix.de

On Thu, Oct 04, 2012 at 01:53:53PM +0000, Johannes De Smedt wrote:
> When I boot my freescale iMX28 board without an ethernet cable, it waits just
> after ADDRCONF: link is not ready. When I plug in an ethernet cable, booting
> resumes.
> 
> [    2.320000] eth0: Freescale FEC PHY driver [SMSC LAN8710/LAN8720] 
> (mii_bus:phy_addr=imx28-fec-1:00, irq=-1)
> [    2.330000] ADDRCONF(NETDEV_UP): eth0: link is not ready
> [   11.320000] PHY: imx28-fec-1:00 - Link is Up - 100/Full
> [   11.340000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [   11.360000] IP-Config: Complete:
> 
> Why does the boot process wait for an ethernet cable? Is there a timeout that can
> be configured (so the boot process can resume faster)?

This looks like a kernel issue, not a ptxdist issue. So this is the
wrong mailing list.

rsc
-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

-- 
ptxdist mailing list
ptxdist@pengutronix.de